We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
I want to know the configuration of Nordic's GPIO pins. I only want to use one callback function, but due to the many buttons on my mouse device, it is not possible to configure...
When I was studying Zephyr, I found that some of the enumerations used by Nordic couldn't be found in Zephyr, so I was wondering if Noridc had encapsulated them in Zephyr...
Hello, as from title, after updating from ncs 2.7.0 to 3.0.2 my application cannot advertise and scan concurrently anymore.
If I start advertising after starting a scan...
Hello,
I would build the Matter nRF Connect Lighting Example Application from the SDK for the nRF54L15-DK. Coud you add support for it in the Matter SDK?
Regards
I am developing a custom USB module based on the nRF54L15 chip. I would like to know how I can initially flash firmware onto the board.
My plan is to have a custom bootloader...
Hi,
I'm working with a custom PCB, with nPM1300 and a microcontroller.
The problem is that working only with battery the nPM1300 VBUS pin show 2.4V and I cannot put...
Hello community,
I have been using my PowerProfilerKit2 successfully under Windows10 for several years now.
Currently I migrate my main system to Linux and would like...
Hello. I have developed a custom board with nrf52840. I am trying to get it running using a bluetooth hids peripheral example in nrf connect v3.1.0. And the main() runs just...
Hi,
I have a field application with a gateway (central) that connects to multiple peripherals for continuous data streaming, in this case 10 peripherals. I notice sometimes...
Has anyone successfully managed to control an led strip (WS2812) with nRF52840's I2S by any chance? I'm trying to use the led_ws2812 sample ( docs.nordicsemi.com/.../README...
Hi,
I'm working on a custom project and I was able to add and edit the overlay file according to my need till yesterday. Today when I tried to build the project I observed...
I am currently working on a Direction Finding project, but I am facing an issue in prj.conf .
I use an nRF52811 custom board for Direction Finding. In the board selection...
I am following the tutorial on Nordic Dev Academy I have a nrf7002dk board and I flashed the code present here . The problem is even if I configure only one channel and I...
Hi Nordic,
I am currently working with the nRF52833 development board and facing an issue related to the APPROTECT feature. Each time I connect the board, the access protection...
HI ALL,
v2.8.0, nrf54l15, using the "periphral_uart" demo without any modifications
I downloaded nrf52840 using v2.8.0 and it runs normally, but nrf54l15 has issues. ...
