Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
I'm using a TI Launchpad , together with the nRF Connect application on my Samsung Galaxy S21. I've got the launchpad connected to my computer and I'm using TI's bTool to...
Hi Nordic
After fellow your youtube tutorials, blinky sample can be built successfully. Flashing code to PCA10090 DK,
the LED started blinky well.
However, it failed...
I have a BLE application (Bluetooth peripheral app) using Zephyr with nRF Connect SDK v1.5.1 and Segger Embedded Studio. I was successful in adding/configuring the MCU Boot...
Hi All,
I'm getting this message everytime I open power profiler, previously working with PPK2, reloading doesn't resolve. Cancelling results in enumeration of PPK2 as unknown...
Hello Everyone,
I'm developing an application which makes use of UART in open thread sdk.
Now, libopenthread-nrf52840-sdk.a library already makes use of UART0, when I...
Hello!
I am trying to sample a digital signal with 12-bits (In a later stage I will need to sample two 12-bits signals). At the moment I am storing the recorded signal...
Hello Nordic team,
I am faced with the problem of developing a custom bootloader which actively pulls FW from an external mass-storage. AFAIK, the SDK only supports OTA...
Hi,
We are using SDK 14.2 with s132 v5.1.0. Reviewing the changelog for newer versions of the SoftDevice, we see:
"Fixed an issue where the application might not receive...
Hi guys,
I am trying to get the PWM rocking. Everything works, but as soon as I define a nrfx_pwm_handler_t in the nrfx_pwm_init, my system crashes with the following error...
Hello Nordic Team,
We are developing a wearable device. We noticed spontaneous BLE disconnections every 1-2 hours. The error code is BLE_HCI_INSTANT_PASSED. I have checked...
We are starting a new wearable device design which will be worn by the user on the chest. We are looking forward to use NRF5340/NRF52840 based modules. The final design is...
hello together,
I would like to use this chip nRF9160-SIAA-B1A-R now only as LTE modem. But the modem should be controlled by two external MCU. Please see figure.
...
Hi support team,
Our purpose is to provide the modules to our customers. We have developped the hardware module based on nrf52832. Now we want to test the BLE mesh functionalities...
I used VDD channel to detected battery voltage, and the P0.5(AIN3) connect to a LED, But I found that after initialize SAADC, P0.5 cannot control output.
Hi Nordic
I have some questions regarding switch to Application on custom address.
The memory layout in flash is like this:
0x00000000 - MBR 0x00000000 - softdevice...
