At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
I entered the bootloader mode of nRF52833DK, but I cannot exit it. When I reconnect the device LED5 is not on and the J-link driver doesn't appear as the removable driver...
I want to increase the throughput as much as possible from the central to the peripheral, but when the number of consecutive calling bt_gatt_write_without_response_cb() or...
Hi,
We are evaluating the nRF52840 dongle. We need to dictate, have a conditional connect feature based on the BLE version. We should specify that use the BLE version...
Hello everyone,
I just wanted to post an important detail when using Nordic's DFU.
After the successful run of the Nordic's buttonless DFU example (by following this...
Hello All,
I am developing a product based on thread protocol.
I am using nRF52840 development kit and nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8 SDK.
I am new to...
After upgrading segger to 5.42 we are now getting the following error when compiling the Bluetooth DFU bootloader part of our existing projects
section .uicr_bootloader_start_address...
Hello,
I am developing an application using
1. SEGGER Embedded Studio.
2. SDK 17.0.2.
3. Cortex-M nrf 52840.
Recently I changed the OS from FreeRTOS to embOS and...
Hello Devzone,
We update our peripheral device(nrf52) with our gateway(nrf52840, central) using the DFU protocol. We have this working and the DFU update is successful when...
Hello,
I am using CUSTOM service in nrf52 for BLE Communication.In the tutorial, there isn't any BLE READ event but I figured that BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST event...
Is there any example for using the Watchdog with the BLE Mesh?
Experiencing some asserts, and would like to restart the device if it happens.
There is an example for the...
I am trying to use the mpsl_radio_notification_cfg_set() API function to configure a radio notification. However, calling the function returns -115, which is (NRF_EINPROGRESS...
Hi:
We are develop an Central Device can Connect 8 BLE Device in same time. and want max throughout. it use queue and freeRTOS. the Central TX is simple.
use sd_ble_gattc_write...
After successful compilation of code the west flash command shows this output after using Tag connect to debug the icarus board with the nrf9160 development board. Normally...
