I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
In my application, I am unable to read back the publish address which was configured during initialisation through mobile.
Please suggest any APIs.
Device: nRF52832
...
HI
The SDK is "nRF5_SDK_for_Thread_and_Zigbee_v4.1.0" and I find a question that is: for all thread programs, add nrf _ delay_ ms () function in while (true) will affect...
I use a sample in NCS1.5.0 to start my project . but examples in NCS1.5.0 are single ble service .always like these: bt_conn_cb_register(&conn_callbacks); bt_enable(bt_ready_cb_t...
Hi,
1. I see the following differences between VDD1 and VDD2 descriptions:
nRF9160_PS_v2.0 P385
2. What are the differences between VDD1 and VDD2 features?
Thank...
Hi all,
I am trying transition from SDK 15.0 to 17.2 and having a branch instruction to itself (an infinite loop) which I think has something to do with the adjustment of...
I would like to create SPI clock timings using the following documents. https://infocenter.nordicsemi.com/index.jsp?topic=%2Fps_nrf52840%2Fspim.html&anchor=topic
1. CSN...
I'm trying to figure out a strange issue with GPS. We have a pretty well debugged and stable system that we're adding some features to, mainly GPS. We're on SDK 1.5, using...
Hello!
I am developing an application which is connecting to an nRF52 board using the Android-BLE-Library implemented by Nordic The application is doing the following: ...
I was looking at nRF52833 as a candidate to use it as a BLE keyboard and USB keyboard (as it has USB2.0)
But in the API documentation section I see that HID keyboard is...
Hi,
I am developing a product using HA.
I am using SDK 3.0 and nRF52840 Dev-kit.
I am using the thermostat cluster, basic, time, power config, and OTA.
Along with...
Hi Devzone,
I use the original MQTT_Sample example, just change "Client ID", "Alive Time" = 120s, use NBIoT + GPS.
Development set up:
ncs v1.5.1, ubuntu, thingy91 ...
Hi,
I followed Getting Started guide for Thingy:91. However, I could not get cellular connected. I am using the iBASIS sim card came with the kit. I am located in Chicago...
This is the output of application compiled with "west build -p -b circuitdojo_feather_nrf9160ns nrf/samples/nrf9160/mqtt_simple":
+CEREG: 2,"FFFE","FFFFFFFF",7,0,0,"11100000...
modem fw v1.3.0
ncs 1.5.0 and master
I'm trying to test LWM2M bootstrapping using https://leshan.eclipseprojects.io/ but my board is failing to connect to the LWM2M...
hi,
im use the usb of nrf52840,and i want to get the event that the usb communicate is build.for example，the usb wire of pc can plug in the usb of 52840，and the usb wire...
