Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hi.
I have implemented the Central and Peripheral NUS service on two devices(nRF52). Since the central knows the characteristic values, I would like to bypass service discovery...
Hi, I've a timer configured by gpiote to capture with a second 'overflow' capture should the signal stop. I'm not using an interrupt instead the CC[0] value is being used...
I have seen the same issue reported.
nRF52840 DK does not appear as a removable drive named "JLINK"
Done the following.
1- My laptop has only one USB port. So I have...
Hi there, I'm controlling the nrf9160 with a esp32 and I'm wondering if you have an recommended libraries for forming AT commands and parsing the return messages?
I'm running through the nrf9160 dk startup guide and I've updated the application and modem firmware. However, it does not look like the application is accepting AT commands...
I have a BL654-DVK (nRF52840) and BL653-DVK (nRF52833). I have a custom program modified from an example that runs and debugs properly on the nRF52840, and am trying to port...
Hi,
We connect our external Board through P20 from EVB NRF52-DK everything goes well.
We are trying to do the same setup on other computer and we get failures to flash...
Hi,
I'm having trouble with debugging the nRF5340. I'm only using the network core and hence use the empty_app_core project for the app core.
The problem i'm facing is...
Hello,
Ubuntu 20.10, nRfConnect v3.6.1, Programmer 1.4.8. Running appimage.
I get:
" Could not fetch memory size of target devkit: Error: Error occured when get library...
hi,
i am working on " ble_app_multilink_central " in ble central . i have connected two peripheral devices .how to include uart in "ble_app_multilink_central" example code...
I have an issue with getting the I/Os correctly setup for antenna switching.
I am running the radio_test example code with the following modifications.
So far, I have...
Hello
I am new to all of this and am wondering if this is possible, and if anyone can point me in the right direction if it is. I am looking to create an open source project...
Hi DevZone Team,
when I use west to configure a project, build/zephyr_settings.txt always contains
"BOARD_ROOT":"/home/user/test/nrf" "DTS_ROOT":"/home/user/test/nrf"...
I am facing one another problem basically i am sending some AT command from central to peripheral but after some time its hang and wait app_erroc. c (__disable_irq();->while...
Hello, I commissioned a factory to make a sample card reader for my company, they didn’t configure everything, because the SDK given to us allows the device to read-only NFC...
