At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
I bought dev board for evaluation purpose (currently run on ESP32)
chip: nrf52832 board: E104-BT5032A-TB ( http://www.ebyte.com/en/product-view-news.aspx?id=956) framework...
Hello Nordic! Im making a custom Nrf5232 QFAA, and for the antenna, I want to use only a grounded micro-coax connector and not a trace antenna, is this even possible? I've...
1. I want to use the following command line to compile the nrf9160 project, but the error.
2. Can you help me find the cause of this error?
3. Please provide me with...
Hello, I encounter a problem when I am trying to measure the current consumption of the nRF52840 on the nRF52840-DK. I have set the board in direct supply mode as described...
Hi,
I'm using a nrf52832 based beacon with some sensors attached. To retrive the current time I use the CTS client. Actually, I'm following the ble_app_cts_c example to...
Hi all,
this is a already known error, and most answers to it is use Segger Embedded Studio or buy the license or so whatever.
But i wanna know how can i manage the size...
Hallo,
i am interested for the nRF52833 and also for the corresponding Development kit which supports Bluetooth 5.1 and direction finding AoA&AoD for positioning. The questions...
Hi guys,
I am using the nRF52832 board and I want to parse and read my JSON file. I don't have too much experience working with cJSON and here you will find my simple code...
Hello,
While trying to build the hello_world project on Thingy 91 using the SEGGER (connection through J-link edu). Following the Hello World project guide given at:
Hello_World...
Hi, I am using BLE as transport and NRF_BL_DFU_ENTER_METHOD_BUTTONLESS as to enter into DFU mode.
My question is:
My application is running at the start and I wanna...
Hello, I wanted to migrate from sdk16 to sdk17, So according to this topic I solve all pre compiling errors, then when I tried to download the code on my board(nRF52832) I...
In the Buttons and LEDs page, the LEDs are connected to P0.28-31 but in the connector interface page, the Figure 1 show LEDs connected to P0.13-16.
Buttons pins also looks...
Hello,
I am trying to create an application on my nRF52-DK using several custom service peripherals, each with 2+ characteristics. I have completed a few tutorials on...
Hi,
I am using USB device CDC, and the COM Port name on the PC is "nRF52 USB CDC BLE Demo (COMX), see the picture below.
How I can change it ? can I change it from...
Hi,
I followed the instructions described on https://github.com/NordicSemiconductor/pc-nrfconnect-launcher but I cannot "Start scan" within nRF Connect. It's greyed out...
