We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello Sir or ma'am
I am trying to load CPP SDK on my nrf52840 DK, But whenever I compile my code it through the error like this," vector: No such file or directory". Now...
Hi, all.
I'm using nRF52832 Software Development Kit, PCA10040, S132.
Using the 'ble_app_uart_c' example, I am studying to connect with my beacons and read data.
I...
Hi,
When evaluated under the following conditions, there was Out of band spurious@325MHz~403MHz (See the following Results ).
Does nRF52832 has spurious(-50dBm~-60dBm...
Hello!
I'm doing the firmware that will be applied to the custom device. This device contains one button, which has two functions. (Function output according to button input...
Hello. I have one multirole device and one peripheral device. Both are nRF53832, SDK version is 15.3 and softdevice is s132 6.1.1. Multirole devices connect to phones as well...
I have two nRF52832 side by side scanning for advertisement with filter by name. Because I will have a number of peripherals advertising, so I want to have multiple centrals...
Hello together,
I want to create a program for the nRF52840 DK and later port it to the nRF52840 Dongle (both from Nordic).
The program should
1) over Serial (USB, that...
Hi there,
I have developed a small sensor device, which generates events when a reedcontact is triggered. When an event occurs a NB-iot message is sent.
However when I...
Hi All,
I'm a student starting a project on a low-power bluetooth accelerometer. I have selected the MC3672 accelerometer ( mcubemems.com/.../) , which will be soldered...
Hello
I am using the ble_thread_dyn_mtd_coap_cli_pca_10056_s140 example and I would like to send 100 bytes of data to display in the logs of the android application "nRF...
hi I am sending a sensor data with time stamp using bluetooth ,now i am sending every data seperately my question is can i store 100such data in structure and send that entire...
Hello,
I have NRF51822 and I need infinite connection. The chip is used as peripheral device. Tx power is set to -8dBm. What is the power consumption when It is connected...
I'm getting a softdevice assertion at PC=0x14CBC after calling fds_record_write(NULL,&record), the record contains the following information:
fds_record_t const record ...
Hi to community!
I have a trouble with nRF52840 when using TWIS. I initialize the peripheral by below code. If the device is reset using default pin 18 by the external...
