Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
I'm working on a BLE central based on the Nordic UART Central example. The peripheral I'm talking to has a characteristic that sends an indication when written to. I'm writing...
Hello Nordic Community,
I found bsd Irrecoverable error on my other ticket
https://devzone.nordicsemi.com/f/nordic-q-a/53913/support-on-nrf9160-irrecoverable-3
I just...
Hello,
I've got a nrf52840 DK and Adafruit nrf52840 Express (less complicated then DK) i'm trying to run a PWM example from datasheet (46 PWM — Pulse width modulation...
Hello Nordic Team
I am working on SDK-v15.3. I have a requirement to update the DFU firmware in lower version too but this SDK version doesn't supporting to update lower...
i am working on a wearable device and want to develop a 1inch wearable using nrf528232 can anyone help e with minimum pcb design requirement for programming.
thanks
I am setting up the DFU example based on NRF52832.
I tried with different version of SDKs (SDK13, SDK15 and SDK16) and all based on armgcc. All toolchains are the same version...
Dear Sir,
I have implemented a program and tested it using BMD-300 Rigado DK.
The program will advertise continuously and I used nRFConnect to connect to the peripheral...
Hi, I would like to capture all bluetooth packets on a specific channel, and get their access code. Same as what Ubertooth does. Is it possible using the nRF52832? If not...
Hi,
I am trying to follow the OpenThread tutorial to build the nRF52840 NCP:
https://codelabs.developers.google.com/codelabs/openthread-hardware/#3
I installed the...
I have successfully completed my bachelor thesis project on a simple wireless sensor network using 3 nRF52 nodes and RPi with using Mqtt and Ble-6LoWPAN example from SDK....
Hi All,
We use nRF52 BLE Sniffer.Its working fiine. Please letus know, weather its possible to sniff multiple BLE devices at a time using single Sniffer. If possible, let...
Will there be an official implementation from nordic of the generic mesh models as described in the mesh model specification or are you counting on each developer to make...
How to change the Bluetooth Mesh broadcast address?
Use the sd_ble_gap_addr_set function to change the broadcast address of PB-GATT ， But PB-ADV still hasn't changed.
...
We are implementing a DFU controller in a microcontroller that communicates with the nRF boot-loader over serial. The target device is nRF52832 using SDKv15.3.0. The boot...
Hello.
I want to see NRF_LOG_DEBUG ("some") through the terminal. When I compile, I get the following error: What should I set or change? MCU : nRF52840 compiler: IAR...
