We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi everyone,
I have a problem with my custom nRF52832 hardware. I soldered my prototype hardware and then I checked if it is correct by checking debugger SW device settings...
Hello,
I'm trying to get as much throughput as possible using the Coded PHY. I noticed that apparently the Data Length Extension feature is not supported together with the...
Sometimes, i found that my firmware still at the old version after update complete, there is no any error.It same happen on use Android-nRF-Toolbox to update firmware.
code...
Hi, I am interfacing external memory chip that is based on SPI protocol with nrf51822. I have to read more than 255 byte via spi in single buffer with 4 byte of command. Even...
Hello,
I am using a custom board with nrf52840 using SDK 15.3 and ICM 20948. I see a lot of twi drivers and its confusing which one to use. I want to read the ICM 20948...
I am using a Windows machine and would like to compile a sample nrf5* project (preferrably nrf52) by using the command line only - no GUI.
Can you please tell me how I might...
currently i set the GENERIC_ONOFF_SET_MAXLEN to 10 and from server i can see the message is received, not one package, but 6-8 packages from client,
my question is what...
I downloaded the nRF Connect SDK v0.4.0-rc1 by following instructions from the Getting Started Assistant, but I am unable to set in up in SES.
I tried to set the environment...
Trying very hard to get up to speed on developing Zigbee devices using the new 3.0 release of the Zigbee stack. The documentation is virtually useless as far as I can see...
Hello,
I am trying to benchmark the CC310 cryptocell on the nRF52840. I am testing the ECDSA example (examples/crypto/nrf_crypto/ecdsa). I can run the code fine with the...
Hello!
I have been working for a while now to get the power on off and default transition time working properly. I have successfully gotten the models to be initialized...
Hi,
I'm using the PPK and with a DK with the nRF52832 and use the S112. When i zoom in i see the current peeks of 30µA in system off.
What can be the source? (Can this...
Hello,
I want to test the IKS01A1 (STM) board with the STEVAL-MKI159v1 board by placing the IKS board in the Arduino connectors on the nRF52 (PCA10056) DK board.
I want...
