Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Checking QDEC (Quadrature decoder) of nRF52832.
But, In a SAMPLEPER Register(0x508) when set to 128us(0) or 256us(1) does not occur SAMPLERDY Event.
On the other hand...
Hi,
I am working on a project running on a nRF52832, using SDK 12.3 and S130. I use Eclipse (2018-12) as my IDE.
I have followed the explanations from this tutorial :...
Hi,
I am using a nRF52832 to communicate with a ICM-20948. I've been trying to write a 16 byte packet of data and read back and verify that same data. According to the ICM...
Hi,
I am trying to communicate from STM32 Nucleo board to murata's MBN52832, using SPI, with the nordic chip being the slave. So, for this I used the SPIS example from the...
Hi,
I am trying to get the ADC up and running on the nRF9160 DK. I had a look for example code and the latest I found was here.
https://github.com/Rallare/fw-nrfconnect...
Hi, I am using N52832 to developing a producation need to implements ANCS NC. I am using sdk 15.2. And I found the connection is terminated by the apple device after the reconnect...
I am using BLE peripheral UART application from nordic SDK version 15.2.0 SoftDevice S140 PCA10056 nRF52840 Development kit on Embedded Segger studio operating system - Windows...
I am trying to design some test cases to check the LTE stability and performance.
I avoid to use the existing Nordic samples to do this as they are too complicate for the...
I am migrating an existing project to nRF5_SDK_15.3.0, and I want to know why the error occurs and how to fix it ...
1. ..\_build\nrf52832_xxaa.axf: Error: L6218E: Undefined...
Hello to everyone.
I'm working with nRF52832 SDK (PCA 10040) and Segger Embedded Studio v4.12, in the Light_switch example for Mesh 3.10. Right now, I'm able to use the...
Hello to everyone.
I´m working with the Light_switch examples (server-client-provisioner) in BLE Mesh 3.10 for nRF52 DK PCA10040. I´m trying to make a network with 2 clients...
The links I found regarding this go to a "OOps" page. I need the original FW of the nRF51DK so that I can use it to flash my target board using nRF51822.
I want to let nRF9160DK communicate with an external module through UART in nRF9160DK
Then I need to assign rx and tx on two pins.
I will use UART0 for printk function...
Hey all!
I have a problem with my custom board using the nRF52832 with Softdevice 6.0 and SKD 15.0.0 working on Windows 10 in SEGGER with the BMD-300. I have the following...
