Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
hi,could i ask you what should i do in order to use ant on the pca10056 board? i added the s340 softdevice but no example works on the board. thanks a lot!!
I am working on a MQTT related application on nRF9160 DK, and grabbed mqtt_simple as a baseline for development. All of my libraries are back at the last tagged releases:...
Hi, I'm confused, according to Bluetooth 4.0 Specification bytes are send in Little Endian byte order, and with LSB first in every byte. So when I receive raw data from characteristic...
When running "pip install nrfutil" I get this message - "Could not find a version that satisfies the requirement antlib~=1.0b (from nrfutil) (from versions: ) No matching...
Hi all,
In Nordic SDK ble_app_gls Example , the following UUID is added as part of Advertisement packet
static ble_uuid_t m_adv_uuids[] = /**< Universally unique service...
Hello,
I'm currently building a project for the nRF52 (using SDK 15.2). I need to have 2 ADC channels, 1 for temperature sensor and 1 for battery level. I figured that I...
I want to let nRF9160 communicate through UART with 3.3V logic level, but the logic level is originally 1.8V.
I have been reading nRF91_DK_User_Guide_v07.pdf, but I'm not...
Hello,
I'm working on the implementation of some custom services and I started to question why the SDK implements the service modules as instance managers (as of SDK 15...
We are having an issue with pc-ble-driver ( https://github.com/NordicSemiconductor/pc-ble-driver ). We're using the nRF52840 dongle. We have compiled and run the `heart_rate_monitor_v6...
Hi,
I want to communicate with a legacy device nrf24l01p+ based using a nrf52840 DK.
Firmware of legacy device setup the card in this way:
I take the esb_ptx esample...
Hi
Getting problem in DFU feature while using segger embedded studio.Device gets programmed successfully but stops working after that.
I am following the same process...
I am looking to check signal strength and would like to be able to do it as easily as possible.
The default asset_tracker sends messages which can be seen in the nrfcloud...
We have an application running on our devices that are using ble_nus to communicate with a base station.
The use case is approximately something like this:
On button presses...
Step1 : init a Client model in Provisoner:
Step2 :config this client:
Step3:set the pub address of this client & control the remote gen_onoff_Server model: but it...
