We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack. ...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi,
In my project I need to send maximum bytes possible inside one package. When using the nrf connect app I can see that when reading the characteristic this works, but...
Hi . I have two questions about the PIPEs in Zephyr RTOS , especially regarding the correct use of the k _pipe _put and k _pipe _get functions :
1 ) In both functions ,...
Hi,
when I configure CONFIG_BT_SETTINGS=y as I want the device to remember the pairing parameters, the services defined with BT_GATT_SERVICE_DEFINE dissapear.
As far as...
Hi,
I use nrf52833 running ncsv2.6.0,
I trans v2.6.0\nrf\samples\bluetooth\central_hids to \ncs_v2.6.0\v2.6.0\zephyr\samples\subsys\usb\hid and now plus usb to nrfUSB...
How do I switch nrf52832 from a broadcaster to a peripheral with a service via a keystroke interrupt? After trying it out, I found that my problem was mainly: I didn't know...
Hi,
I'm trying to control nrf9160 SIP from stm32 MCU via AT Commands. Should I program on the nrf9160 the AT_CLIENT sample for this purpose or is not neccesary?
I'm trying...
Hello Team, We are currently working on a project for interfacing Larger TFT LCD display with Capacitive touch with nRF5340 Devkit board and SoC. As per the datasheet of the...
Dear Nordic,
I'm unable to register an nRF9161 device on the Verizon Thingspace IoT Network. They have a web UI which allows one to enter an IMEI, ICCID pair. When I enter...
We use custom board with NRF52840 and a MODBUS CO2 sensor. We are struggling with power consumption when the serial is enabled. The goal is to take measurements and then put...
// <i> NRF_FSTORAGE_SD uses the nrf_fstorage_sd backend implementation using the SoftDevice API. Use this if you have a SoftDevice present. // <i> NRF_FSTORAGE_NVMC uses the...
Hi to all,
I have a problem and a question regarding the power measurement setup I’m working on.
Regarding the problem, I am trying to measure the power consumption...
Hi All,
I have a couple of nRF9160-DK which I use to program custom boards through the Debug Out port. Both DK work perfectly well until now. One of them can't program custom...
Hello everyone,
in our Project we want to use the nRF52840 DK with the X-NUCLEO-NFC08A1 (ST25R3916B) extension board as an NFC Reader.
In the SDK 2.5.2 are samples for...