Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi, I am new to BLE mesh. As I have understand , a provisioner is one which forms the mesh network and assigns addresses to the node and make them join to the network.
1...
Hi,
How do I-
1. Start a timer when sending data from nrf to host (PC) in form of input report.
2. When the application running on host machine receives this data, send...
When i try to add RSSI viewer app in nrf connect it shows error
Unable to install: Unable to download developer.nordicsemi.com/.../pc-nrfconnect-rssi: net::ERR_CONNECTION_RESET...
I am experiencing strange behavior on the PCA10056. I have two boards now in the same state, both were working fine before starting work on the Secure DFU (uart). The following...
I found that App timer using in ble_app_template in different modules. Is it possible to change prescaler value without harm to other modules? I need to increase maximum value...
Respected nordic community,
I am working on one project where right now i try to make custom service read operation through nrf52832 in segger studio. From my device(mobile...
HI, I am seungwoo
I am developing data transmission using nrf52810.
A 300-kilobyte file is divided into 220 bytes and transmitted continuously.
11-27 17:24:24.416...
Hi,
I'm developing a unit which i need from time to time to send a packet throw I/O lines (F.E.virtual uart)
However the packet bit timing is very critical.
As far as...
Hi, I am using nrf52832 with SDK 12.3.0 and nrf 52 dev board. I am experiencing a problem whenever I programmed nrf 52832 using nrf52 dev board and NRFGO, after certain number...
Hello, I'm currently using the nRF51DK with Wireshark as a BLE advertisement sniffer. So far this setup has worked great, but I'd like to make a small modification for development...
Hi all,
i am currently working on 5 nrf52832 DK boards, i want to use nrf mesh for indoor positioning system. I am currently using nrf sdk v15.0.0 and nrf mesh v2.2.0. ...
Hi.
We are on early phases of getting UART DFU support for our product. However I seem to run into communication issue with the bootloader even with the examples provided...
Should the DEBUG compiler flag be removed before flashing a board that should enter sd_power_system_off? I've seen some troubleshooting guides mention that Debug mode can...
I have set up the thread border router. I connected the NCP (a nrf52840) with a usb cable to a raspberry pi. Now I wonder if it is possible to connect the raspberry pi with...
Hi all,
Currently, I am working on Nrf52 DK with nRF52832 on Keil IDE. My focus is MQTT with 2 nRF52s and RPi. I have succesfully used examples in SDK, but now I am trying...
