We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi.
So I'm trying to configure my SW to use two uarts (as I've understood that uarte and uart are separate modules that can be used at the same time).
As the app_uart...
Dear nordic,
I implemented a uart in BLE application its works fine.
I need to reduce current for that i enable and disable uart but when i call function disabled or enabled...
hi team,
real quick; The accuracy internal reference (0.6V) used in the SAADC is specified in COMP section of the data manual as +/-3%. The gain error in the SAADC is...
Hi,
I was just trying to build the light_switch_provisioner_nrf52840 code using Segger Embedded Studio. However, I've got a error build/light_switch_provisioner_nrf52840_xxAA_s140_6...
What is the function of db_discovery_init (); , I am migrating a code from SDK 8 to SDK 14.2 and I can not find that function, I do not know what library it contains or how...
Hi Nordic.
I am currently working on nRF52810 chip and the main power source is lipo battery. The battery is charged via USB could you recommend an efficient power management...
Hi,
I am currently migrating my controller from nRF51 to nRF52832 . I am facing an issue where in when I try to do an TWI communication with MPU9250 on nRF52 the code gets...
Hey
all process of burning work great without use of reset pin.
question is do we need to change it and wire pin to jtag connector?
what is the added value of the pin...
Hi All,
I have been using Keil but have decided to test "Seggers Embedded Studio for ARM" to develop firmware for the NRF51822. After following this tutorial i have been...
Hi,
We were working on a board that communicates with another board from a customer. It seems that the customer's board has voltage spikes sometime (it has 110 VAC signals...
We create general purpose device based on nrf52840 chip and need to provide different ways of dfu: buttonless, usb, uart. Is there any examples, recommendations how to do...
NRF52840 = GCC/GNU ARM - SDK 15.0 - SD 6.0.0 - Builds tested under windows & linux on two separate machines. Chip is Fanstel BT840E-V2 module on a custom board. We've been...
I'm very newbie in bluetooth mesh. So the question is ..
1.Can I execute any of peripheral abilities (I mean spi, twi, adc, pwm and etc) on device that works like a node...
Hi,
I use the nRF52840 DK with Segger IDE.
I would like to use different peripherals on the MCU (GPIO, SPI, Timers etc), but I would like to avoid using the Nordic SDK...
