Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi everyone,
I would like to know if it is possible to establish a serial communication to a PCA10028 card using Adafruit Bluefruilt LE friend knowing that there is no...
Hello everyone,
I am using nrf51822 chip that has functionality to flash bl, sd or app using mobile app application. I want to reuse this functionality in order to have...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
I am using the ble_app_uart example as my base on a 52832 with sdk 12. My project runs off line power and needs to remain available for connection 24/7. I have commented out...
I am communicating with a temperature sensor (MLX90614), which has flag register. However, in order to read this register, I must send a read sequence without issuing the...
Hi,
As has been mentioned many times, the DIF on both the nRF51 and nRF52 consumes quite a bit of current. In the past, on the nRF51, I've relied on power cycling both chipsets...
Hello,
I would like to make changes in ble_app_uart_c example for connecting to a custom peripheral.
Service Uuid of my peripheral is as follows : 99aa0001-d0e3-44ce-a306...
Our homeowners association has a gate which opens when a transmitter in the car is pushed. I would like to add a BLE device to the gate which would trigger the gate to open...
Hello all,
So.... i'm quite green to the Nordic and Bluetooth protocol.
i want to program NRF51422.
what i have now it the Nordic test board and a spi-canbus print. this...
With custom hardware and softdevice flashed on board (using BDM_350) when I try to debug I get and error: with () at 0xfffffff9
It appears to come from address 0x3a2
...
I currently have a Braveridge device which uses an advertising rate of 50 Hz (connection interval is 20ms)
CONNECTABLE_ADV_INTERVAL is set to 0x0020
sd_ble_gap_adv_start...
Hi, I am trying to determine if there is an error in the generated code or if I am not performing the actions correctly. I am trying to Update Characteristic User Description...
Hello,
when a bootloader wants to update the softdevice, I think it has to first store the SD binary somewhere in flash memory and then to use sd_mbr_command to ask the...
I'm trying to debug the Experimental IEEE 802.15.4 example on a nRF52840-Preview DK Board PC10056 with IAR Embedded Workbench ARM 7.70. Compiling and linking the project is...
I am working on nRF51422 with SDK 12.3.0, S130 v2.0.1, Keil C.
I got a problem in initialization my custom service. When I add some characteristic to SoftDevice, it returns...
