Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hello!
I have a problem when scanning and advertising at the same time with a NRF51822 and S130 v.2.0.0. (SDK11).
I can start both scanning and advertising without any...
Hello,
I am designing a PCB layout using nRF52832, I want to make it as small as possible so I am considering to route all component tracks to another layer.
I want...
Hi,
For an application I have a nRF51 at my disposal and I need to transfer about 3'000Bytes. I found in the documentation that the nRF51 can use the S130 SoftDevice which...
Hi.
Using PCApp/MCP(v 3.10.0.14), How can "BLE_GAP_EVT_SEC_INFO_REQUEST" occur?
Or will not it occur?
If it occurs, please tell me how to do it.
Thank.
Hello,
I need help about the multirole with the Freertos.
When I take the code example from Nordic "C:\Nordic\nRF5_SDK_13.0.0_04a0bfd\examples\ble_central_and_peripheral...
Example project: blinky_FreeRTOS_pca10028.uvprojx
I include SEGGER_RTT.h file.
After execute vTaskStartScheduler() function.
SEGGER_RTT_printf(0, "Hello World from SEGGER...
Using C11 compiler, and a Makefile from a template, where the Makefile defines CFLAGS with -Werror I get:
.../components/libraries/util/app_error.c:47:5: error: narrowing...
I running the (nrf52) HRM profile with FreeRTOs and connecting the BLE device with the Nordic Toolkit app.
On occasion the connection to the BLE device fails. After repeated...
Hi, I want to interface BLE module with freeRTOS. Does nordic provide BLE stack for freeRTOS? and if yes then is it opensource? or is there any standard BLE stack which can...
Hello,
I want to design PCB antenna for nRF52832 chip. I took reference from nRF51 dongle hardware layout.
I wanted to spread antenna upto 18mm width so I reduced the...
Hi
The j-link detects the chip, but for not obvious reason the j-link and keil will trough an error when I want to program the chip, here is the j-link out put. do you have...
Dear All,
I would like to order Li-Po batteries for my nRF52840 development kits and need some information. From the battery, what type of female battery connector is needed...
Hi, I can't get 250Kbps working on the nRF24LE1. I'm using the enhanced shockburst examples in the nRFgo SDK (enhanced_shockburst_ptx_nrf2 and enhanced_shockburst_prx_nrf2...
Hi,
By mistake, I clicked 'fill with zero' button in Jflash, may I ask, is my chip bricked because of this? Thanks.
The following lists my steps:
program the...
