I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
After i test a lot of possible configurations for nrf24L01+ based on the documentation, i didn't come to the right setup for all the nRf24L01+ registers to send data from...
Hi,
I'm using Windows and I am following this tutorial.
I am at the point where I need to write make at the example project.
I get this error
as warned in the...
Hi,
I'm trying to get a general idea of how the radio will perform near the bottom end of the supply range.
Our product concept is currently designed on a system voltage...
Hi,
I stuck on SOFTDEVICE_HANDLER_INIT in example code on nRF DK PCA100028 within debug.
It is example code from SDK 7.1.
How Can I solve this?
Why Nordic's SDK...
Hello,
I am developing an an system and I am at the stage of optimizing for power.
I using NRF6707 ( Very helpful !!) to measure current.
I cut SB9 of NRF52 DK and have...
Hi,
Can I try to discovery services for the next connections while it is performing for the other connection?
I use "ble db discover" manager.
And I cant find this...
I'm using nRF52DK and SDK12.2.0.
Trying to change MTU size.
When I modified app_nrf_uart example as below
#define NRF_BLE_MAX_MTU_SIZE 103
Then infinite reboot...
I am working on a project and have successfully implemented single channel PWM to dim leds (using a transistor FET).
The pwm init code is below:
uint32_t err_code;
nrf_drv_pwm_config_t...
image description (http://)when i try to flash the led binky programme to nRF51822 Ek. i am getting device error and LED also glowing continuously.
1.this device error was...
So I was thinking of having the following:
nRF24L01+
to balun (e.g., Johanson 2450BM14A0002 or Anaren BD2425NnRF)
to PA/LNA RFX2401C
to PCB antenna
If...
Hi all,
I want to clarify are there any deference between "connection_id" and "conn_handle" ?
I use a multilink central application with 8 possible peripherals devices...
Hello,
I have some difficulties to make an ant acknoledgement with my nrf51422 (s210), and i would be grateful if you could help me with it. (SDK used 12.2)
I have 2...
Please give me info about configuring a timer at given timeout. For eg,. if we want to blink LED for 30 seconds, how to configure them using timer events.
