Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
The Peer Manager is currently in experimental state and is not recommended for production and same for the device manager for some sdk.So which SDK should be preferred
Hi,
Im using S130softdevice.i wanna make dimmer by using experimental_ble_app_blinky project on gpioet
But i have a problem with detecting 10 milisecond time (it means...
Hi,
I am new starter in Nordic platform. I am using device nRF51822-CFAC, the SoftDevice is S130_nRF51_2.0.1(Id: 0x0087).
What I am doing is to put NRF51 into system...
Hi,
I'am tring to test the dfu by secure bootloader.I had done all steps like: Test the BLE Secure DFU Bootloader application by performing the following steps .But I found...
I am implementing an SPI master to communicate with an accelerometer using the SPI HAL directly. My chip is marked nrf51822QFACA11609AC. I have implemented blocking functions...
Hi,
When the UART is configured to use FIFO , i use the UNUSED_VARIABLE(app_uart_get(rxdata));
to read a buffer from FIFO.
how can i also receive a number of bytes...
Hi,
I want to do this cycle with GPIO without interrupting it on NRF51 with BLE softdevice:
PIN1 to HIGH level
read value of PIN2
PIN1 to LOW level
Repeat...
Hello, I'd like to do directed avertising to a central which has a random private resolvable address. My idea: both devices share a pre-defined IRK so the peripheral can compute...
I tried, but it does not work.
for(int y=0;y<100000;y++)
{
if(nrf_uart_event_check(NRF_UART0, NRF_UART_EVENT_TXDRDY))
{
nrf_uart_event_clear(NRF_UART0, NRF_UART_EVENT_TXDRDY...
Hi,
We have a little issue that we at the moment need to cycle power on v3 nRF51822 after DFU.
We have determined the the reason has something to do with the whole complicated...
I attempted to add spi_master as below, but I am in trouble with link error.
If anyone knows the cause, please tell me.
*** Using Compiler 'V5.06 update 4 (build 422)...
I'm working on a project based on the ble_app_uart_c central example in SDK 12.1. I'm polling the RSSI of a Nordic beacon using sd_ble_gap_rssi_get(), and the fastest update...
I want to handle 3.3v in nrf52832.
NRF_GPIO_PIN_S0S1 -> NRF_GPIO_PIN_H0S1
Can this be this way?
If not, what should I do?
Also, Can the PWM output to 3.3v?
