I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
Hi,
Do all NRF51822-DK (development kit) have the same silicon build revision? If not, which distributor should I approach for the latest revision and is there a specific...
I have encountered a problem with the IAR linker where I run into a 32k code-limitaion, even though I have a licence with no limitations. According to IAR, the problem may...
I was playing around with examples and decided to implement a custom service that sends the RSSI as a single-byte characteristic value. Here's the init function:
static...
Hi,
I'm trying to connect to BLE and send data on UART. I'm using nrf51422 with softdevice s310 and SDK v5.2.0.
The following code gives me error 3003 which I figured...
Hi,
I think getting started with the Nordic chips is not as easy as some others.
I would like to know what are the first things that I need to run my code on a Nordic? Especially...
I just got the nRFgo Dev Kit, and going through the set up I see I need a nRF6310 Motherboard, but I can't seem to find anything about it - like were to buy it.
I just downloaded their iccv8cortex trial version and it includes the 51822 as a target. My 5 minute test drive not withstanding, it looks like this might be a good option...
How to reduce power, for bond connections such as cscs services which only requires communication once per second?
Is there a way to manually / automagically turn off the...
Before I call sd_power_system_off(), I do the following:
NRF_TWI0->ENABLE = 0;
NRF_TWI1->ENABLE = 0;
NRF_ADC->ENABLE = 0;
NRF_SPI0->ENABLE = 0;
NRF_UART0->ENABLE =...
Hi
I using nRF51822 ble_app_uart project with softdevice 7.0.
I need to manage my internal flash memory map so i cannot use pstorage libary test main.txt .
So i try...
Hi,
What is the typical range of operation that can be achieved by nRF51822 Bluetooth Smart Beacon Kit ? I know it depends on the Tx power, but can a range of approx 30ms...
I need help choosing between 2 technologies above, my goal is to enable multiple (up to 20) devices exchange small amount of information (around 30 bytes) between each other...
Hello
How many packets can the nRF8001 send in a single connection event? I have seen here, that it is possible to send up to 6 packets with the nRF51822 + Softdevice S110...
Hi, we've been using nRF51822 for developing application and iOS 7.x detect then just fine.
Since I upgraded to iOS 8. Beacons are 'invisible' to our application.
I was...