Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
Hi,
I am working on the XIAO BLE SENSE board which has nRF52840 SOC with P25Q16h 2MB flash and other sensors
I want to access the external flash to store sensor data....
Hi Nordic Team,
I am currently developing applications for custom boards using the nRF Connect SDK v2.6.0, focusing on the nRF52840 microcontroller.
In our ongoing project...
Hello,
I am using the nRF54L15-DK development board running the official hci_uart example as the BLE controller. My own Linux system acts as the host using BlueZ to control...
Hi Nordic team,
I noticed that when using the external FEM (nRF21540) with the nRF54L5 device, the power consumption at a transmit power setting of 8 dBm is significantly...
Hi, I have implemented a soft UART in the VPR FLPR. I am having trouble power managing it. I see an unexplained extra 500 uA current draw after I start the CPR until I reset...
Hi, for nRF52840 raw proprietary RADIO mode, do TXADDRESS and RXADDRESSES imply a hard total node-count limit for a custom multi-node network, or only a simultaneous hardware...
SDK is NCS2.9.2,My device supports master-slave integration. As a slave, it can pair and bind with a mobile phone. As a master, it can scan and connect to two slave devices...
HI
I’m doing secondary development based on periodic_sync_conn in NCS 3.2.1 .
After establishing a periodic advertising sync, I have two issues:
Sometimes the buf...
Hello,
I'm trying to set up auto-provisioning and onboarding in my project as described in this sample: https://github.com/nrfconnect/sdk-nrf/blob/066ac6f61fe19ad91d805fd788d782e245f09a2e...
Hi,
On nRF5340 with external flash (SDK 3.2.x), is it possible to both support serial recovery enabled for both cores while supporting simultaneous DFU?
It seems like...
Hi,
i am developing under ncs 3.2.3 (then toolcahin 3.2.3 -> nrfutil-device 2.17.1).
FLashig OTP registers using batch method, i am getting the following "error" on nrf54l15dk...
Reference: first consult as Case id. 305571 Replyed by Tobjorn
I have a working proyect in wich 485 cable communication was replaced with NRF24L01+ but I need some help...
In the enqueue function esb_write_payload , the enqueue implementation uses ++tx_fifo.back .
In the dequeue function esb_pop_tx , the dequeue processing also uses ++tx_fifo...
I'm working on a project where we're planning to use XIAO BLEs on an OpenThread network, for that we need very low power consumption. I've been trying samples to get low consumption...
Hello, I have followed the guide to do a serial recovery of the appcore and it's working fine. Now I would like to be able to update both the appcore and the netcore. I have...
