I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
I have the nRF Hw v1, and it seems like I did something wrong with a Fw:
nRF is recognizable by a computer as the COM3/4/5 device:
And it is accessible with the nRF...
Hi.
After migration from SDK2.7.0 to SDK2.9.0 I have issues with power mangement. CONFIG_PM_DEVICE_RUNTIME=y, which I used, causes that twi driver doesn't start. I try to...
In the nRF5340 Audio DK example located at C:\ncs\nrf\applications\nrf5340_audio , I want to add a third board and communicate with it from the master (gateway) to send commands...
Dear NRF Team,
I hope this message finds you well. I have been following the steps provided at the Dev Academy for the initial setup of the IDE. However, I have encountered...
Hi, I am facing an issue while integrating BLE with the rest of my code. The code crashes when I try to start BLE outside of main() .
Currently, I have placed the BLE initialization...
Hello,
our project which started 7 years ago with SDK13.0 has been migrated some time ago to SDK 15.3 and now to SDK17.1. At the beginning we were quite happy with the RTT...
i am unable to build the unit test code with kernel file
FAILED: CMakeFiles/testbinary.dir/home/avinash/zephyrproject/unittesting/gce-source_code_latest/app/vipr/model/gas...
I'm trying to program an nRF54L15 on the nRF54L15PDK evaluation board with the DEBUG IN SWD pins (P15). On my setup I have a J-Link PLUS connected to P15 and a USB-C connected...
I have the following settings in my prj.conf:
and getting the error
CONFIG_FLASH_MAP was assigned the value y, but got the value n. Missing dependencies: FLASH_HAS_DRIVER_ENABLED...
Dear Nordic team,
we are facing a strange phenomenon - in idle mode (k_sleep(K_FOREVER)) we notice, that the current consumption drastically increases if a magnet is placed...
I have a production system running a modified asset_tracker_v2 sending temperature data to AWS. All is working fine with V2.5.0 on several hundred sensors. I am trying to...
Hi,
I am looking for procedure to make it work nRF240L01? I am getting documents for Arduino but as you know that is not understandable, with Arduino it worked but i don...
Using the Online Power Profiler for LTE we saw that nRF9160 would require 0.115 s to upload 4-kbit of data into the mobile network.
This is an U throughput of ~34-kbit/s...
Hi,
I want to make an I2C communication with an NRF5340 DK as Master and an NRF52840 as Slave, but all the example i found in I2C communication it use the slave adress...
Hi!
I’m developing an application using nRF SDK 2.9.0 with the Xiao BLE Sense . I created a new project based on Zephyr’s UART peripheral example.
The application runs...
