Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
Hi,
Again the topic which has already been discussed several times in this forum. I just want to share my experience and perhaps help other users having difficulties.
...
Hello, I noticed that the SoftDevice Controller for nrf5340 in nrf Connect SDK 3.1.0 reports a bluetooth version of 6.1 (LMP Version 0x0F), yet the QDID for it ( Q360820)...
Hi,
NCS v3.4.0
BLE peripheral_uart example
nrf54l15 DK with ns config
in the Chinese (double bytes) Windows, need to add encoding="utf-8" in tfm_parse_manifest_list...
Hi Nordic team,
I am currently researching Bluetooth Channel Sounding, where I have setup two nrf54LM20-DK as intiaitor and reflector respectively.
I am using NCS 3.3...
Target device: nRF9151
NCS 3.4.0
Memfault Integrated
FOTA architecture in place with four slots, 2 in internal flash and 2 in external flash
Background COAP updates...
Hi,
My central device is running into Bus fault when continuously sending data to multiple connected peripheral device and any of peripheral device got disconneced. Issue...
Hello, our design does not use the USB block of the 52833. In the electrical schematic we have connected VBUS (AD2) to GND and we leave D-(AD4) and D+(AD6) open. Due to a...
I am looking to evaluate Amazon sidewalk on the nrf54L15 dev kit and have also bought both of the Semtech evaluation boards LR1110MB1LCKS and SX1262MB2CAS. The nrf54L15 is...
Hi:
I use sdk ncs3.3.0 and nrf54lm20dk.
Failed to return using AA dfu_target_init.
OTA firmware is zephyr.signed.bin.
I: DFU header I: 3d b8 f3 96 00 00 00 00...
HI
I am currently carrying out secondary development for PAWR based on NCS 3.2.1. I understand that its communication adopts frequency hopping. I would like to ask whether...
I hope, as a non-EE, I'm clear with my challenge ...
My student EE designed a small PCB with a couple of sensors (CO2, temp/humid, microphone) with an nRF52811. The boards...
The goal is to have the nRF52833 stay in sync with GNSS time without the external pulse per second for some significant time (some minutes). This is not possible with a normal...
how to configure uart communication between nrf54l15 and tc334 via uart and i need to control my nora b2 evk leds based on mesage from tc33 using tlv can anyone give me idea...
Dear Nordic team,
Please tell me the theoretical power consumption of the nRF54L15 when using CH—both for the initiator and the reflector.
Best Regards,
Riki Yosh...
I installed NRF Connect, the BLE plugin, and successfully flashed the dongle firmware. IIn NRF connect, the BLE plugin scan button is disabled. 'Quick Start' was unable to...
Hello,
I've been asked to create a new ticket for this. It follows on from
@ Erlend Isachsen asked:
So before marking this problem as resolved, it would be nice to be...
