I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Hello,
im new in programming for Bluetooth.
I would start it to create a Bluetooth App for Android to control a relay.
The old App for this is not obtainable anymore...
Hi, with the new version of vs code ( 1.76 ) i found that intellisesnse doesn't work.. when i put the cursor over a function and click on it, nothing appear and over the cursor...
I would like to use the oscillator pins (if possible), NFC pins, and pin 11/21 as GPIO. I can see why 0,1,9,10 would not work but I am confused why 11 and 21 do not. Every...
Hey there,
I have been doing research in the NRF52 series in the knowledge center and it is a little difficult for me to do the research in this way. I was wondering if...
I'm trying to build a test code on NCS to continue developing nRF52832. However, even if you simply follow the steps in VS and just Config, it won't work.
Same with v2.2...
Hi guys. May I ask one firmware code question for ble_app_hids_keyboard_pca10056_s113 project from 17.1.0 nRF5 SDK:
When sending "C a p s o n", this uses a DO-WHILE...
Hello Team,
I am working with the nRF52840 microcontroller and I would like to know how to check the output clock frequency of the controller like any "Clock_OUT" pin present...
Hello We are using sdk 17.0.2 and softdevice s140_nrf52_7.2.0_softdevice We are using both central and peripheral mode in our application. First we start advertisement and...
Hi Engineers,
I am trying to play an audio file from SD card, so I have interfaced SD card module and i2s module to the nrf52840.
I am able to read all the files available...
Hi!
The software version I use is SKD16 and nRF52810 chip is used for development.
When using the key function, it is found that the bsp driver will have extra power consumption...
Hello!
I was wondering what methods exist to optimize either the configuration or code to get the lowest power consumption with the nRF Connect SDK?
Before I used the...
I have tried fixing this issue for a few hours to no avail.
Here are the error messages I am getting:
13:12:28.854
Using nrf-device-lib-js version: 0.5.0
13...
I'm using the Mesh SDK v5.0.0 (for the main Mesh code), the nRF5 SDK v17.1.0 (to facilitate normal BLE GATT connections as part of this device's core functionality), and developing...
I am working on SDK17.1 with SES. I am developing an BLE application that has bootloader (buttonless dfu), softdevice(s340 7.0.1) and fds. My application requires some data...
nRF Connect SDK Version: 2.0.2
Network core image: hci_rpmsg
I have an nRF5340 device acting as a peripheral. When I initialize advertising with the BT_LE_ADV_OPT_FILTER_CONN...