Hi! Could you clarify a bit about Bluetooth mesh gateways' implementations. I wonder to know possible ways of Bluetooth mesh gateway implementations. How is it possible right...
Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Dear Nordic,
Do we have ready-to-use keyboard driver with scanning/debouncing?
I've not found an example or docs about using KSCAN with gpio-connected keyboard...
Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
Hiya!
I am writing code to add support for USB on the NRF58233/58240 to MakeCode. MakeCode relies upon WebUSB. At any point, a user can close the website which causes...
I noticed the minimal b0 immutable bootloader build does not fit anymore.
I used the example here: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples...
Hello,
We are using NRF52832 to design a loss preventer product ,can you help to review the design SCH and PCB layout before PCBA making ? main including RF desing , GPIO...
Hi, I was trying to a project that includes edge impulse and nRf5340DK. I successfully run the example project t they provided and now try to use the library provided by edge...
Trying to do DFU over ZigBee, but nrfutil failes:
Gets this problem constantly. I have check all the examples and everything, doble checked all parameters, but always the...
Hello.
I am trying the SEGGER Embedded studio's open nRF connect SDK project, but it fails with an error like the one in the image. How can I make it succeed?
SEGGER...
I am doing something really really crazy, that's writing some application on PC using opcode serial port for configuration a light switch server (maybe light switch client...
Hey all,
I've been using the SDK for Thread for quite a while and got all the basic stuff up and running with Thread and the nRF52840DK, RPi Border Router, etc.
For example...
Hello, I'm working with nRF5340 DK with Zigbee communication. I'm getting RSSI values between 0-255, but I'm more interested in the value in dBm, so I would like to convert...
Hello,
I developed the code on nRF52-DK with Segger.And also I want to program this code to MDBT42Q chip with nRF52-DK.
What are the circuits and software programs where...
Hello, I' trying to use the Serial LTE Modem application on an Actinius Icarus board. I configured the nRF project for the correct target, enabled COAP support, set Nb-IoT...
After upgrading the nRF-Command-Line-Tools from 9.8.1 to 10.12.1 the RTT output of JLinkRTTClient stopped working when doing a nrfjprog --reset. Interestingly it still works...
Hello, i've tested dfu process from secure_bootloader with different app examples with success (ble_app_blinky, ble_app_uart, even a custom application) but, when I try the...
Hi, I want to use normal GPS data (not AGPS) to send to my MQTT server.
I work well with MQTT_Simple to send sensor data to my server.
I see a GPS example in /nrf/samples...
Hello,
I have application that is sending data over BLE every 5 minutes.
I want to implement DFU using BLE. I don't have any single button on my device.
What should...
