Hi! Could you clarify a bit about Bluetooth mesh gateways' implementations. I wonder to know possible ways of Bluetooth mesh gateway implementations. How is it possible right...
Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Dear Nordic,
Do we have ready-to-use keyboard driver with scanning/debouncing?
I've not found an example or docs about using KSCAN with gpio-connected keyboard...
Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
Hi,
Do you have a sample ANT radar profile example with all the pages defined, similar to ant_hrm.h in SDK 15.3 components/ant/ant_profiles/ant_hrm/pages/?
Thanks,
Abid...
Hi Admin,
I just bought development board Thingy 52 from Digikey. I coudn't find design files that consist of hardware design in Nordic website. Could you advise for this...
Hello,
I am currently tweaking the Thingy:91 to run a stripped down version of my custom application. I have been able to flash the device with the Thingy:91's sample at_client...
hi,
we're using a Adafruit nrf52832 board for a building a ble keyboard . w're able to pair to two central devices and appear to them as a keyboard , but for example : we...
Hi, we are designing a product that needs LTE connectivity and BLE for local setup.
The nRF9160DK uses an nRF52840 with some links for COEX and comms.
Is there any reason...
Hello,
is there any kind of good practice available about how to generate UDP traffic with the nRF9160DK via NB-IoT for a simple test?
As far as I know the AT client...
Hi
I followed below tutorial with my nrf52840 using SDK 15.3.0
https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts/ble-advertising-a...
Here is the software: https://www.nordicsemi.com/Software-and-Tools/Development-Tools/nRF-Sniffer-for-Bluetooth-LE which notably doesn't support the nRF52 dongle
I also...
SDK15.3
nRF52840
S140 v6.1.1
Q1. I have an RTC compare event connected to a Timer count task over PPI. The Timer is configured in low power counter mode. My question...
Hi, I am strugling to get the power comsumption down to the number I have been reading on this forum. I followed the instruction of the dev kit manual . When measuring the...
Hi, I'm getting regular crashes with my app: SOFTDEVICE: ASSERTION FAILED. Using and NRF52832, SDK 15.3.0, SD 132 6.1.1, and Mesh SDK 3.1.0. With DEBUG defined, I don't really...
I'm trying to interface 2 SPH0645 mics to the nRF52840 DK.
Little did I know when I bought them (the mics) that you need to waste 2 timers + 2 pins + memory space to make...
Hi,
I am trying to measure a signal using the SAADC driver on SDK 13. I have used the example from the nrf52 playground for low power ADC
I have a few questions on best...
Hi,
I have a nRF91 development kit and want to connect P4 to the Segger Jtrace for ETM streaming. In the manual, it stated that a 2×10 pin 1.27 mm pitch surface mount connector...
Hi,
Is there any way to get network time without previously setting it with AT+CCLK?
I would like to implement sort of "fake time" by initialising it with the network...
