Dear Nordic,
it's about USB implementation. We need to add interface string descriptor for ineterface name. Using USBD_STRING_DESCR_DEFINE(primary) I've added that to string...
Hello, I have NRF D 24LU1P 1201FD and NRF F 24LU1P 2136IW. The first one executes all commands, while the second one does not work for writing and erasing. I tried to erase...
Hi! Could you clarify a bit about Bluetooth mesh gateways' implementations. I wonder to know possible ways of Bluetooth mesh gateway implementations. How is it possible right...
Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Dear Nordic,
Do we have ready-to-use keyboard driver with scanning/debouncing?
I've not found an example or docs about using KSCAN with gpio-connected keyboard...
I updated the firmware of my Nordic Thingy 52 to the latest version 2.20 using the Android app on my smartphone. Now I cannot use anymore the standard webapp ( https://developer...
I have this problem with all the samples for the nRF9160. When I build the zephyr.elf file, I get an error saying it failed. Please see the picture below. Any idea what's...
Hi,
SDK: nRF52_SDK_12.2.0
Softdevice: Generic_Stack_S332_02.00.01.hex
TX_PIN_NUMBER: on port 25
RX_PIN_NUMBER: on port 26
In our application we are using two...
Hi, We would like to support Bluetooth 5 in an upcoming product development.
Bluetooth 5 gives us two options for an improved connection: Twice the data through put (payload...
Hi,
I am using the Thingy:52 (that contains the nRF52832) and also have evaluation board of nRF52840.
Does anyone have a recommendation for a DAC for use with one of these...
HI,
May I ask, what is the version of J-LINK officially supported in sdk 15.3? I can not find it in release note.
See.
The following toolchains/devices have been used...
The Config Model Publication Set message can be used to configure a model to periodically publish its status.
If a model doesn't support publishing the `publish_timeout_cb...
Hi,
I've added WFE\WFI to my application running on nRF52840 on my RTOS Idle Hook.
Runs fine when debugger is attached , but when debugger not attached - the application...
Hi
I have merged NUS client , NUS server and multilink examples.
It works well and no problem in functions.
Now i will make that the module(with multilink nus server...
Hi guys,
sorry but first of all I have to admit that the migration is a mess. And really do not understand why you entered nrfx and did not make a clear cut. Because saving...
Hi I want to get the peripheral address from the UART and compare with scanned peripheral addresses from the central (nrf52832) and if the received address string is of one...
I'm using a custom PCB with a Laird BL651, which contains a nRF52810.
I've been following the "Transferring Project to nRF52810" tutorial here to run one of the simple BLE...
Hi
This is in part related to my previous post on PWM signal generation on two channels that are 90 degree phase shifted. The frequency of the PWM signal generated was...
Hi,
I am using nrf51422 in my project.So we are using keil5 u vision project and sdk 12.3 version so here the problem is when i tried to open the blinky project it is showing...
I need to add ARM_MATH_CM4 to my preprocessor definitions using Segger Embedded Studio.
I know this has been dealt with in "nRF52832: How to Include the "arm_math.h" library...
