How to prevent storage partition from erase durning MCUBOOT firmware update?
I use Settings with NVS to store data
CONFIG_FLASH_MAP=y
CONFIG_FLASH=y
CONFIG_SETTINGS...
Hi,
I am building a Thread network ( www.youtube.com/watch with a Rasp Pi 4 as a border router, an nRF52840 DK as an RCP, and an nRF5340 DK as a child to be added into the...
We found a problem with a client's legacy design. They use two 12 pF load capacitors for the 32 MHz crystal, which has a 4 pF capacitance. This is a somewhat unusual Abracon...
Hello DevZone,
I have a project where I currently use the AT%XPOFWARN feature, in order to turn off the modem in case the battery voltage is too low. It's used in both cellular...
We use several Nordic chips in our BLE sensors. We bond to the devices from Android, connect to update configurations, then disconnect such that the device then advertises...
Dear Nordic DevZone,
I'm encountering pairing issues with mobile devices and a nRF54 DevKit flashed with HCI over UART firmware. After initial pairing, deleting the bonding...
Hi, all!
Is it really possible to timestamp 4 GPIO edges in parallel with the nRF52?
It would need to be as fast as possible and some edges might be simultaneous so...
hello:
I'm looking for a bluetooth solution for our equipment. We need a chip that simulates a serial port, what we send by SPI port, it is received in the mobile and the...
Hello,
I would like to understand how can I make use of the macro ERR_TO_STR_TWI in order to know what error is being given by my TWI module function.
I have tried something...
I am attempting to run the SoftwareSerial example on the Arduino Primo.
The example code does not work and I am wondering whether the pin assignments are correct.
Example...
If I use PWM "nrf_drv_pwm_simple_playback"
and that will go to "start_playback"
How can I catch end point after it finish entire function?
BTW, the process will keep...
Hello All,
I am working on nRF52-DK, nRF52832 PCA10040, and i want to know on how i can wake up my device from sleep mode using hardware interrupt. I am using interrupt...
Hello,
i want to power off and on the board using the Long Press Button Event.
Is this possible? Please help me out to resolve this issues...
Thank You
I used to get all my output by running cat on /dev/ttyACM0. Now I only see the first few lines, until the filesystem gets mounted.
How do I prevent Linux mounting the filesystem...
The Bluetooth Mesh Light Switch example provides an example of how to program a Bluetooth Mesh application where the client model is on the provisioner device and the server...
Hello
what we want :
One central and several periphals.
The periphals will have different DEVICENAME.
Is this possible with the NUS Service?
The doku says ;
Note
...
Hi all,
Anyone has tried if the Tx power of nrf 51822 is changed from +4dBm to -20dBm, how much power (%) can it save, in a ballpark figure?
Thank,
Carl
hi
i am using the sdk 12.3.0 when i'm trying to compile the file under blinky/pca1028/s130 i'm getting this error anyone can help me please
............\components\softdevice...
I am using S132 V5.1 in combination with nRF5 14.2, and I cannot find where I can set hvn_tx_queue_size.
We are using the new option to configure the softdevice using the...
any one can help me to fix this erreor please
............\components\ble\ble_services\ble_nus\ble_nus.c(41): error: #59: function call is not allowed in a constant ...
Hi,
I am trying to send an command line through UART to the UART device such as MP3 audio module.
MP3 module is taking only hex values. How to send it to the UART device...
