How to prevent storage partition from erase durning MCUBOOT firmware update?
I use Settings with NVS to store data
CONFIG_FLASH_MAP=y
CONFIG_FLASH=y
CONFIG_SETTINGS...
Hi,
I am building a Thread network ( www.youtube.com/watch with a Rasp Pi 4 as a border router, an nRF52840 DK as an RCP, and an nRF5340 DK as a child to be added into the...
We found a problem with a client's legacy design. They use two 12 pF load capacitors for the 32 MHz crystal, which has a 4 pF capacitance. This is a somewhat unusual Abracon...
Hello DevZone,
I have a project where I currently use the AT%XPOFWARN feature, in order to turn off the modem in case the battery voltage is too low. It's used in both cellular...
Hello,
I am currently evaluating options for integrating Bluetooth Low Energy (BLE) functionality into a medical-grade device that requires time-sensitive communication...
We use several Nordic chips in our BLE sensors. We bond to the devices from Android, connect to update configurations, then disconnect such that the device then advertises...
Hi,
i have a strange problem which happens when i use scan mode to get 3 separate channels on saadc.
For example when i use uint32_t ticks = nrf_drv_timer_us_to_ticks...
Hi, I use Keil 5 and SDK 13.0.0 in Windows 7 64bit desktop.
I wished to test the SDK 13's BLE UART example.
However, even though I clicked "Check for Updates"...
basically i tried am trying the easiest ble example
ble_app.becon_pca10040
i tried the following.
use keil to upload into the nrf52 Evalutaion board. the led is...
Hello, i have been looking for a good development environment to use for my nrf52832 on linux. I have only found a few repositories on github pertaining to this. Not very...
Hello,
Does someone know a good J-link segger for programming the nrf51822 smart beacon kit?
And do u need a 6-pin j-link segger for the nrf51822 smart beacon kit?
hello ,
I am interfacing Grideye AMG8832 with Nrf51822. The initialization part is executed without errors but ON trying to recieve or transmit it gives error of TWI as...
Hi Nordic developers.
I am developing a custom board using 2 Rigado BMD-300, but I am unable to run my 100% operative program or examples.
At first time I was able to...
Hello,
I am using SDK 12.2 currently but I would like to follow the BLE Tutorials offered on this site, which I see were written for SDK 11.0. Will I have any issue following...
Trying to program an MDBT42Q nRF52832 based BLE module from an nRF52-DK as external target on connector P20.
I used to do this with nRF51-DK and external nRF51 modules with...
Our product is a peripheral on the nRF51822. We develop on Mac and use gcc, make, etc with Visual Studio Code rather than Eclipse. Recently, we started getting close to production...
Hello,
I would be interested on knowing whether I may have a secondary UART on the nrF52 chip or not. I would like to communicate my nRF52 with a RN2483 and this is done...
Hi
I've just looked into the new released SDK 13.0.0 with support for the new S132 4.0.2 and the new PCA10056. On line in the release notes reads "This release does not...
I'm using the serialization code with pc-ble-driver for S130 (version 0.5.0).
I randomly get a deadlock in the serialisation code.
It can happen after a call to read, write...
Hi,
I want to know that what should be the supply voltage to NRF52 IC. Another thing is that we want to connect our product with NRF52. Our product has TTL wires which...
Hello,
Is there any methods to implement the "long press wake-up"? Pressing the button for 3 seconds to let device enter sleep mode and pressing the same button for 3 seconds...
