SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
I am trying to use second virtual interface of NRF7002 to use with custom linux driver. I intended to use it to add support of STA+AP or STA+STA mode. However, I observing...
Hi,
I am using nrf SDK -16.0 with board nrf52840. In Ble 5 we are using LE Coded PHY with S=8.
for Ble 5, the average current consumption got doubled when compared to...
This seems like it should be simple, but I cannot seem to set a custom static BlueTooth ID on an nRF52832 under PlatformIO / Zephyr - it just keeps generating a random ID...
Hello,
We are currently developing a Zephyr-based connectivity solution using the NRF5340 alongside an NRF7001 WiFi chip. Since we also want to use Bluetooth we have implemented...
Hi All, I'm working with MAX86916 sensor and trying to measure the FIFO/RED/IR/GREEN/BLUE data to measure SPO2, Heart Rate, Heart Beat but I'm not able to read any data on...
Hello,
I want to control LED of the Server 2. (Turn on / off) by using Client.
How to add the relay node in light switch example (this is one of the basic example...
I am trying to update a device using a Macbook pro with Sonoma 14.4 and am receiving an error message that states that nordic "Did not receive checksum response from DFU target...
hello, I'm using nrf52DK & connect sdk v2.6.1. I'm in the process of migrating from nrf5 SDK to connect SDK.
My previous code to read Mac address to form unique BLE names...
I am getting a warning in my nrf5340 overlay file because I ran out of pins and need to reassign P0.30 to my BMI270 interrupt 1. Here is the message in the overlay file: ...
I am using visual code studio, zephyr RTOS, v2.5.2 on NRF52840
I am trying to find a QSPI example
I noticed someone mentioned the sample :spi_flash is using QSPI ? But...
Hi,
I'm migrating my application from SDK v2.4.1 to v2.6.1. In my application I'm using Zypher BLE Controller with HCI_rpmsg child image. I renamed the hci_rpmsg to hci_ipc...
Hi.
Can you please tell me how to erase the chip in VS Code without writing new firmware?
In Segger Embedded Studio there was such an option (Target -> Erase All), but...
Hello,
I am currently trying to figure out why my application stops working after some time (can be hours to days).
Im am using a nRF9160-DK, with the nRF91 programmed...
Hello,
I am working on a BLE application based on the nRF52840 and NCS 2.5.0.
I'd like to reduce or disable the packet retransmissions. I've looked through the NCS documentation...
I have a firmware project currently developed in a Nordic nRF52840 chip. I am trying to create a new board ( we are updating the PCB ) to implement the same firmware on a...
