We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi.
I am developing the nrf52832 seger embedded studio.
I tried to use mutex using nrf_mtx.h, but there was an error.
I don't know why this error is coming out...
I adding custom module o asset_tracker_v2. In Main.c using the function static void data_get(void ) , various data requests are added using the instruction:
app_module_event...
Dear Nordic Engineers
I use NCS 1.9.1 test Advertising Extensions,I have a problem.
I use softdevice controller,if I not set "CONFIG_BT_LL_SW_SPLIT=y",the program will...
Hi Nordic,
One of my customer is evaluate Thread for their product.
They can set up the Thread network with nRF52840DK now.
But we can't found the API of transmit...
Hi,
We are developing a custom hardware that has MDBT42 module with nRF52832 chip on it. Our project is based on the ble-throughput example and this module is using the...
Hi Support,
i did some changes(add some folder ) in gps sample program for nRF9160DK(v1.1.0) and using nRF SDK connect , toolchain 1.7.1, and getting error ( error: Aborting...
Hello
I am working on to flash my firmware binary into external flash by using nrfjprog commandline tools.
I have used below command to program and verify the external...
HI,
I am using BL653dvk board(customized ). I am following this link ( https://devzone.nordicsemi.com/f/nordic-q-a/82430/ncs-external-flash-ota-change-qspi-to-spi ) and...
Hi All,
I usually use nrf Connect for desktop in conjunction with the nrf52 Dongle (nrf52840 chip) to perform DFU's on my devices during development. but recently I have...
To get this example working, both major cellular providers here in NZ, Vodafone and Spark (M2MOne) require a specific (different) APN in order to access their networks.
...
Hi, I want to connect my PC to nRF-52840 through BLE. I git nRF connect for desktop and downloaded the BLE software to another PCA10056 and i managed to connect but i can...
Good morning,
We have a new equipment based on the nRF52840 and s140.
Just now, a new problem has appeared and it is very strange, as it seems to be a ‘random’ error:...
Hello,
I am currently using Fanstel dongle, where I am trying to trigger the USB DFU with nrf connect programmer (buttonless). The example which is provided works on the...
Hello,
I am using an nrf5340dk and I am trying to create a qdec sample using as reference the wheel module.
I have added set the CONFIG_SENSOR and CONFIG_QDEC_NRFX to...
Hello Nordic Experts,
Recently, I have been investigating the radio timing for advertising, I tried to find answers online, but I failed. To explain more clearly, let...
