At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hi ,
We have deployment a ble mesh solution developed with NRF mesh sdk version 5 with the bootloader provided with the SDK. Now our requirements have increased and we are...
Hello,
we have a zephyr application on nRF52832 DK with nRF Connect for vscode
Before we added DFU support, we had a power consumption of 28 uA
After adding DFU support...
3 months ago Nordic stated the following
The S140 version 6.0.0 SoftDevice does not have full support for S=2 (500 kbps). The application cannot select S=2, so all packets...
Hi Nordic guys,
I'm developing with nrf5340, and meet some problem with writing external flash - nrf qspi flash.
I found it sometime failed in 'flash_area_write' and return...
Hi,
I'm using SDK17.02 on nRF52810, when my application have an error, it will log "fatal error" but never reset system. BTW, I'm not debugging and just watching the RTT...
I 'm developing a program (C# ) on PC for the nRF52840 dongle (pca10059) that is a RSSI scanner.
Scanning different BLE channels in the environment. The program is much...
Hi Sir,
We plan to test the WebUSB example under the below path:
/ncs/1.8.0/zephyr/samples/subsys/usb/webusb HW: nRF52840-DK When we compile, program and connect to the...
I bumped into some compilation errors regarding PRS box4, when I tried to remove UART from an example.
I saw that PRS is "Peripheral Resource Sharing", but it looks like...
I am working on nRF Connect SDK 3,9.3 version. One day a dailog to update appeared. I clicked to update while SES was also opened and I was working on a project. Suddenly...
Hi,
I am working on a firmware and have added custom services to HRS example on SDK 17. I want to know if its possible to add BLE multiperipheral capability to my device...
I don't have enough pins to dedicate a SPI bus to the nRF21540.
In the webinar I attended I believe I heard that the SPI bus is not supported by the current SDK anyway,...
Hello everyone,
This was discussed before, elsewhere ( link) , however, it is meant for the "nRF51422 chip " and I need to resolve some other points too ...
it is necessary...
Hi,
I am working on the sample DFU OTA project as recommended below,
https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/ncs-dfu?CommentId=3cb5df69...
I am developing an applicaiton to run on the app core of an nRF5340, and I have mcuboot enabled for the purposes of handling DFU.
I have recently implemented signing the...
