Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Hello there,
I got an error msg when I tried to compile the Bluetooth LE UART service example for nRF54L15-DK as: " devicetree error: /chosen: undefined node label 'uart0...
Hello, I' needing some help on setting up the MCUBoot for the BL5340PA using the ncs 2.6.2. Currently I have the below add on for the prj.conf for the application core:
...
I am using the LORA Drivers provided by zephyr for testing my SX1762 lora module with NRF52833 Development Kit. I am able to initialize and configure the LORA Peripherals...
Hi,
I am working on an FCC cert of our product which is nRF52811 based. We are currently on SDK 2.0.0. I have copied from the nrf samples bluetooth area the projects peripheral_uart...
1.After I burn AP CODE, executing "nrfjprog -f nrf53 --program factory_data.hex –sectorerase" instruction will cause the following error. This issue wasn't happened in prior...
I am trying SPI Master/Slave communication between two nRF54L15-DK boards, using the nRF Connect SDK v2.8.0 and nRF54L15-DK 0.9.1 and 0.8.1. However, it seems that the SPIS...
Hi,
I just got my Thingy91x up and running, and it’s been on for a few hours now, but it has already used 460/500 location requests. How often does the unit send location...
Hi, I am trying to flash to a new design which uses ublox NORA-B120 module. I am trying to flash from vsc. But the flashing fails with following error.
Anyone can help...
Hello,
I have configured 2 nRF5340 boards for LE audio streaming from my mac. Two things I am noticing:
1. The audio is streaming but it is intermittent. Audio plays...
I found out nrf_reset_network_force_off() can be used to turn on/off the network core in firmware, per the example in NCS v2.5.0, samples/subsys/ipc/ipc_service/icmsg . I...
Hi,
I am making an application based on the peripheral-nus example. The checking for CR is removed and all characters are just sent further when available. The problem is...
Hi, I have developed a stable program on the nRF52840 board, and now I'm transporting all the code, and trying to make it compatible with an nRF54L15 board.
I used ZMS to...
Howdy,
I am currently working on the nRF52840 chip and trying to convert my SPIS code from being in my main while loop into being interrupt driven. I am using Zephyr to...
Hi!
I want to integrate power management into our FW. Therefor I did enable it in the prj.conf:
And added runtime enable and action run calls regarding this device...
