Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hi,
I want to use a MPU6050 sensor with my nrf52832 board.
I connected the SDA and SCL pins of my sensor board with the pins P0.26 and P0.27 of my nrf52832 board, respectively...
Hello. I'm working with multilink example and I've got some problem. I want to send data to specific peer device, but after restart central or one of the peer, they reconnects...
Hi. I have a problem with Segger Embedded Studio. I always get more than 100% of RAM usage when building project on SES, even if examples projects from SDK . Anyone know what...
Hello, I have the following question. I'm trying to program my firmware via DFU Bootloader and nRF Connect (smartphone). That works perfectly with the test board SparkFun...
Hi,
I am using the two units talking with each other for the BLE uart.
One is running with the example ble_app_uart_c_central. The other is running with the ble_app_uart_peripheral...
Hi, After updating my nrfConnect to 3.6.1, I had issues using my J-link being unrecognized in the programmer app. The J-link I'm using is part of a Silicon Labs Dev Kit, checking...
Hi, I was wondering if there are any problems with connecting VDD to an external power supply when using nrf52840 in the high voltage mode? I would like to connect VDDH to...
Dears,
1.I want to know when working at USB CDC mode, what's the phy rate could be supported? And what's real rate is it？
2.Could customer customized their private protocol...
Hi,
I've read that highly secured IoT devices have a hardware root of trust. One very important feature of it is a private identity keys to prove identities for mutual authentication...
Hi,
I noticed at least using pwr_mgmt we are calling two times nrf_pwr_mgmt_run for every interrupts ! All interrupt seems to be triggered twice ! Or wakes from idle state...
HI Nordic
I currently have a 2 separate projects, that i'm trying to merge.
- Production test tool with RTT CLI interface on nRF52840 (Here I use JLink.exe -device NRF52840_XXAA...
Hi Nordic teams,
I'm developing the function of Mesh DFU. I've test the nrfutil tool locate on https://github.com/NordicSemiconductor/pc-nrfutil/tree/mesh_dfu , and it works...
Hi All,
I have designed one device using nRF52840 MCU and software SDK nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71.
From Software end all features are implement and...
Hi Sir,
As check nwp_024_v1.6.pdf, it only shows the tape real information w/ below series.
nRF24
nRF51
nRF52
nRF8000
nRF9160
I don't find the information for...
Hi,
I have a SPI peripheral connected to the nRF960 DK. In order to access this correctly, I need to be able to write a byte to a specific address first and then read back...
