We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Just wanted to share how to interface a thermistor (103) with Nrf52840 and get the values over a BLE android app (Nordic toolbox). refer here,
github.com/.../Thermistor...
Just wanted to share the project for interfacing IR distance sensor with Nrf52840 and get the values over BLE app (Nordic toolbox)
github.com/.../distance-sensor-with-N...
Hi..
I am working nrf52832 with accelerometer sensor, I want to store the data about 100hz for 1sec in flash, I want to store it an array and send it over ble how to do...
- I used https://github.com/NordicSemiconductor/Android-BLE-Library version 2.1.1 and https://github.com/NordicSemiconductor/Android-Scanner-Compat-Library to code My Ble...
We plan to develop a temperature and humidity sensor based on nRF52832, which needs to evaluate power consumption to confirm battery selection.
are there any similar data...
Hi,
I am working on internal flash nRF52832 merged with twi sensor, my sensor function will return a string . How to assign the string to the my_data.p_data . i am getting...
I'm trying to optimize an Azure project based on the Asset Tracker example. I was recommended setting CONFIG_SERIAL=n in both the Application FW and SPM. However when I add...
Hi,
I based a new device design on the Thingy91 antenna and tuning circuitry and noticing that the current consumption of the two QM12038's negates the amazing power efficiency...
1.In docs I see: “This example requires one of the following SoftDevices: S112, S132, S140”. What is the reason not to support S113?
2.Is there a way to accomplish functionality...
The Cloud_client sample application does not work in this version.
The connection with the nRF Cloud is disconnected immediately:
I: Network registration status: Connected...
Hi, I am trying to add a secure button less OTA service in my application.
1-I have successfully added service but showing the following error.(I can see OTA service in...
Hi,
We have been working with a Zigbee coordinator based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b, Softdevice and FreeRTOS.
Zigbee task defines a...
Hi,
Is it possible to add a custom characteristic to a standard BLE service? I wish to add a CO monitor with ESS (0x 181A ). If yes, how to add a 128 bit UUID with this...
Hello,
I want to output in one pin 400kHz and inverse of 400kHz in the other pin. I have somehow managed to output the the 400kHz but haven't managed to output its inverse...
