We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
HI,
I was trying to update firmware on thingy 91 using MCU bootloader. Now when I trying to upload again it is keep showing one error.
Error while probing devices: Error...
Hello,
I'm using nRF52832 and SKY66112-11 PA/LNA connected to increase the range. I'm using nRF5 SDK 17.0.2 and nRF5 SDK for mesh 4.2.0
I followed this guide to use PA...
Hello everyone,
I'm programming for nRF52833, using SDK17. When I program for scanning filter (SCAN_NAME_FILTER and SCAN_UUID_FILTER) and debug, I got these errors. I don...
I have a ST link V2 with swd interface support. For one of our existing projects ( custom board ), we want to examine the current consumption of BMD-350 ( NRF52832 ). Hence...
I am currently tasked with programming the NRF52810 to boot up upon a button press and then sit and wait for further button presses to trigger various functionality including...
Good afternoon
According to the project requirements, two keys were added to the compiler settings for stricter project verification:
-Wsign-conversion - Checking for...
Hello,
I have tested the ADC+UART in nRF52 BLE module,
and now thanks to help of this community, I can get the ADC value with UART communication.
Sorry for so many questions...
Hello I have an issue with the exit.c file, Eclipse tells me: exit.c:(.text.exit+0x16): undefined reference to `_exit' I do understand that this is a linkage problem that...
Hello Sir or ma'am
I am trying to load CPP SDK on my nrf52840 DK, But whenever I compile my code it through the error like this," vector: No such file or directory". Now...
Hi, all.
I'm using nRF52832 Software Development Kit, PCA10040, S132.
Using the 'ble_app_uart_c' example, I am studying to connect with my beacons and read data.
I...
Hi,
When evaluated under the following conditions, there was Out of band spurious@325MHz~403MHz (See the following Results ).
Does nRF52832 has spurious(-50dBm~-60dBm...
Hello!
I'm doing the firmware that will be applied to the custom device. This device contains one button, which has two functions. (Function output according to button input...
Hello. I have one multirole device and one peripheral device. Both are nRF53832, SDK version is 15.3 and softdevice is s132 6.1.1. Multirole devices connect to phones as well...
I have two nRF52832 side by side scanning for advertisement with filter by name. Because I will have a number of peripherals advertising, so I want to have multiple centrals...
