Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
Hello Nordic team,
I'm looking into solution to pass data to my application after a Reset using the RAM of my nrf52840.
Looking at the documentation, this picture troubles...
Hi,
I have a question regarding BLE timeslotting. In my setup I have a master with multiple slaves and equal connection intervals set at 7.5ms. The slaves acquire data that...
Hi,
I am using nRF52 to complement BLE function of MTK7628(they communicate through UART),I've implemented most of the functions.Now I want to add OTA to nRF52, so I use...
I'm trying to combine these 2 examples. I tried adding the uart code:
uint8_t cr;
while (app_uart_get(&cr) != NRF_SUCCESS);
to apps_ble_uart while loop and the whole...
Hi all,
I´m trying to create my first BLE application with segger embedded Studio.
My Hardware is the nRF52833 DK with a sensor connected to dev Board via I2C lines...
Hi, there in inconsistent data about the number of UARTs in the nRF5340 OPS v0.5.1:
- Page ii (nRF5340 features) states "Up to 2x UART (CTS/RTS) with EasyDMA" for the application...
Hello.
I'am new to developing with The Thingy 52 and just trying out simple things. I wanted to see if i could toggle/set one of the pins high from the code but havent had...
Dears,
I'm trying to run the mbedtls library with thread safety with the freertos, already defined MBEDTLS_THREADING_C and MBEDTLS_THREADING_ALT in the user_mbedtls_config...
I have never used the GPIOs near the RF pin (GPIO 22, 23, 24), until my latest project, which I needed to due to pin limitations. It is normal for pins adjacent to RF outputs...
Hi.
I try to test using ble pc-drivce C library & 52840 dongle on pc.
except custom service. everything is fine.
under below is custom service pic.
...
This seems to be a recurring question. I suspect the Wireshark/nrf-Sniffer setup is delicate enough that minor changes/upgrades in any of the components causes a problem....
nrf52832 , SDK_V15.3 , ble_app_uart sample code , data communication problem.
Hello there...
I use the SDK V15.2, ble_app_uart sample code, on the nrf52832
seems the...
Hello,
Currently working with Segger 4.42 and SDK 15.0
I've searched around the devzone on doing a passkey connection between my server and central.
I've used the ble_app_gls...
