Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hi engineers, I got a question regarding nRF52840 (PCA10056), i want to run DTM using PCA10056 board with MT8852B tester. Unfortunately, i keep failing to get the EUT address...
Dear all,
Our application is made of
Chip nRF518122 + SDK 11.0.0 + DFU Bootloader + BLE application (gcc complied) loaded with nRF Toolbox over the air
we are putting...
Hello,
the nRF9160 product specification 1.0 states in 5.1.4.2:
"Note: The LTE modem requires using LFXO as the LFCLK source."
I checked the clock register and noticed...
Hi,
I have developed an SWD working code which read-write the Flash Memory and RAM which is working very good.
Now I have a problem in I need to write start address...
Due to time pressure, I'm starting this thread based on an existing ticket: https://devzone.nordicsemi.com/f/nordic-q-a/51423/firmware-on-custom-board-application-bootloader...
Hi team,
We have a customer who has some questions about GPS.
The questions are:
Where do we save the Ephemeris data when GPS code start? RAM or flash?
When use...
Hi,
Can an nRF5x device be configured as a BLE relay with Bluetooth Mesh?
I believe with the Central-Peripheral-Relay example, the Relay needs to establish connection...
Hi. I am trying to create a dfu zip file that contains the softdevice, bootloader, and application. I am DFU upgrading an NRF52 device from SDK v13 to SDK v14 via Nordic's...
Hello,
we are using the nRF52840-DK.
File: secure_bootloader_ble_s140_pca10056.emProject
File: ble_app_buttonless_dfu_pca10056_s140.emProject
In short, we are...
Hi,
I have a well working cli environment under linux where i can compile, program and debug a nFR52 demo board.
I have installed RSSI Viewer (1.05) and Bluetooth Low...
We want to deactivate Mesh DFU packets relaying from the App side to avoid messing with the bootloader firmware. Is there any flag we may use for that?
Hi,
I'm trying to use a Bulk IN endpoint (EPIN3) and am running into an issue.
I call the nrf_drv_usbd_ep_is_busy() function to test whether it is safe to proceed with...
Hello
I am using buttons less DFU,
S132_nrf52_6.1.1 softtdevice
using Android + nrf connecct, I can update the device with DFU
using IPhone 6, I can not update...
I am able to provision using BlueZ's meshctl tool on Raspberry Pi3. However, after restarting meshctl, I am not able to control my device. I tried the "connect" command after...
