We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Is there a set of directions for configuring the peripherals for the nRF9160 SPM.
I need to change the default configuration shown in the SPM sample.
I tried editing the...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’ and “nRF Connect” app.
To save battery, I want...
Hi,
I am in the process of upgrading our project to work on the version v0.4.0 of the SDK. I managed to make it build but I had to remove the code that depends on the configuration...
We use the app scheduler in our app and I recently needed to increase the EVENT_SIZE passed into APP_SCHED_INIT. I changed it to a value that is not an event 4-byte multiple...
Hello,
I am using SDK 15.2.0, nrf52840, s140.
We are using SPI for an analog Front End initialization. SPI initialization works successfully done. But when we read or...
I have one node.
This node have two model.
I want to one model having relay function, another not relay function.
This function can implement?
SDK : Mesh SDK 2.1...
Dear experts,
Currently I'm using the peripheral device(s130 softdevice) and central device(s120 softdevice) both base on nrf51822 to evaluate BLE connect time. The connection...
I am beginner in nrf programming. I want to use NRF-ESB protocol to communicate between my Rx & Tx device with maximum battery saving techniques. For this i am using nRF5_SDK_12...
I enabled BLE buttonless unbonded secure dfu on custom nRF52382 based chip with s132 (SD version 6.0.0).
When buttonless service dfu control point characteristic is written...
I have established a connection with max30205, but I get only the first byte of temperature, how to read the second one? to get the tenths of a degree.
Now it works like...
Hi, I need to use a ble_hrs_t variable between two different files, I used the BLE_HRS_DEF() macro to instantiate the variable in a header file that I've included in both...
I am using the example from ble_app_att_mtu_throughput_pca10056_s140, changing the values for:
#define SEC_PARAM_BOND 1 /**< Perform bonding. */ #define SEC_PARAM_MITM...
Hi, I am following the Thread Border Router example provided in the info center. I have one Raspberry Pi 3 v1.2 connected to the internet via WiFi, one nrf52840-DK programmed...
