Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
i am using nrf24l01+ on arduino devices, one arduino device as master, and other arduino devices as slaves. I like master to broadcast a radio (dataToSend) toward all slaves...
nrf52832, keil with startups from sdk13
Initialization:
IntHandler:
With one event everything working well. Then I add another:
I need to measure SENT signal...
hi.... folks
i am using nrf52840 development kit , and i debugged the merged programs such as uart and twi program in it .does it will give the temperature data?
i am...
Hi all,
Please refer to the SDK version : nRF5_SDK_15.2.0_9412b96.
We need to use two uarts simultaneously for module & device respectively.
For example :
UARTE0 ...
We, I am using nRF 5 SDK v 14.2.0.
Power-off has occurred during program development. I can not identify the location, Functions that are not memory leak, buffer overflow...
Hi,
Now, I am using the nRF52840 to develop and do signal test. Can you share me some tool that can make the board enter the test mode?
Best regards
Simon
Hi:
PREJECT: nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_hrs_freertos\pca10040\s132\arm5_no_packs
When TWI0 and GPIOTE are turned on at the same time, the...
I'm trying to get the AT commands sent in the asset_tracker example written out together with the other printk statements. I have tried adding this to the prj.conf: CONFIG_LOG...
I used the nrf52840 as the central device, use SDK15.0, scan then connect the peripheral toys.
sometimes i found the central can scanned some ble peripheral but can't connected...
Is there a way to have 6 different GPIOs act in unison off one event/action? I need all 6 to go ON and OFF at EXACTLY the same time based of an event or action.
I'm trying to program a thingy:52 device, via the nRF52 DK, with the .hex files from this repository:
https://github.com/NordicPlayground/thingy52-mesh-provisioning-demo...
I would like to see if I can get 5V switched from the DK. Is this possible?
I see the 5V rail on the diagram but I didn't find the documentation to describe it.
I can...
Hello there,
I am currently trying to read the leftover WS2812b LED strip data which was sent using a single channel I2S. The data sent from the board (through I2S) looks...
nrfx/nrf52840_bitfields.h not define I2S_CONFIG_MCKFREQ_MCKFREQ_32MDIV6-2.
But nrf52_bitfields.h is defined this.
nrf52840's datasheet is written,MCKFREQ 32MDIV2-32MDIV125...
