Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Due to a hardware design error, the CLK/Data pins on TWI bus was switched in different PCB versions. I want use software to dynamically detect the situation and switch the...
hello
yes I have problems with my app_timers in SDK14.2 (migration from 12),
I well noticed that the prototypes of the functions create and start changed from sdk12. ...
I have an application that performs a task and saves the result to EEPROM that uses an ATMEL ATMEGA168pa processor.
I want to convert it to the nRF52840 which does not have...
Hello! We have been trying over the past week to figure out how to best back up a provisioner/client so that if it goes down we can rebuild the network without re-provisioning...
Dear Team Nordic,
dear Community,
I'm working on a project with nRF24L01+ transceivers where I have two types of devices: a so called Basestation which acts as a Primary...
Hi all,
I am using nRF SDK for Mesh v1.0.1 and I want to implement following as in picture:
I am publishing to group address (group address because in the future I...
Hi, I test the SDK example "temperature", it works OK. I copy the code to my project, there is no compile error, but when the code running on the DK pca10040, the code is...
Hello there,
I'd like to bond between two nrf5 modules and have a real time communication between them.
Now my question is what is the role each would have to play...
The nRF5 SDK is event-driven. So does it mean that the event handler in my application will be directly called in the interrupt service routine? If I write a long event handler...
Hi all,
I'm experiencing a performance drop with BLE proxy enabled in Mesh SDK 2.0.1 compared to Mesh SDK 2.0.1 / Mesh SDK 1.0.1 without proxies (higher packet loss, range...
Hi,
I have project for NRF51822 in IAR(EWARM). Short about project: it based on example BLE to UART communication; it uses SPI, I2C, analog inputs readings, some digital...
I used nRF5_SDK_14.1.0_1dda907.
I opened the bpwr channel then received ant+ packet.
The device received ant+ packet successful.
How do i know that how long time the...
hi all ,
how to build multi provisioneers with mesh network ?
i read some information and run the nordic mesh sdk 2.01 (ligh_ swith sample )
i have some issue with...
1. I am issuing a gatt characteristic (CHR1) write without the response requested from Central (BLUEPY/BLUEZ, Ubuntu 18)
2. Central than reads CHR2.
Is it possible...
