We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Segger provides great information for the use of the JTrace for tracing and profiling with the NRF52 development kit here.
https://wiki.segger.com/Tracing_on_Nordic_Semiconductor_nRF52832...
Hi,
I'm expecting using a custom board with nrf52832 running connectivity program as a host to connect to the perpheral, and the hrc v5 example of pc-ble-driver is used...
hello support team
I am trying SDK Proximity coexistence example
I am using Mesh SDK 2.2
and nRF5_SDK_15.0.0_a53641a
I followed the steps given in link
I am getting...
Hi All,
i am working on SDK-14.2, i am facing issue with ble disconnection in dfu mode.
by using nrf-Connect in mobile i am upgrading the firmware, but it lost connection...
Details:
nRF52832
SDK 14.1 with matching SD
Compiling with GCC
I am trying to solve the following problem:
My device is powered by a coin cell (Manganese dioxide...
Hi, when my program calls sleep_mode_enter(), it enters system off (deep sleep) as expected. However, when I press the button on the Thingy52 to wake up, the bootloader starts...
I have problems connecting to a NRF51802 via stlinkv2 and openocd. I also tried a black magic probe flashed onto the blue pill board. Both did not work. I have ordered a NRF51822...
SDK 15.2
The nrfx_uarte_event_t callback contains a nrfx_uarte_xfer_evt_t; structure,
this structure has the bytes field as a uint8_t this should be a uint16_t to support...
Hi,
I'm using nrf52dk and SDK v15.
In my application, I have 2 input pin and I want to disable one of them when in one of the 2 pins occurs the event low to high, is it...
Hi All,
I have an issue with bootloader, in this i am successfully transferred application but after that my application not started.
i am just upgrading the sdk from...
Greetings,
I'm having the same weird issue as this question, though I don't understand the answer to it https://devzone.nordicsemi.com/f/nordic-q-a/34447/app-gets-stuck...
Hi everyone,
I've a nRF52810 based device that I am working with the Android based nRF Connect app on a Poco F1 (Oreo 8.1.0). The app scans the device properly but connection...
I just got my new nRF52840 dongle and went through the procedures stated. But I tried programming the nrf blinky firmware and after that I'm not able to connect the dongle...
