I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hi.
After migration from SDK2.7.0 to SDK2.9.0 I have issues with power mangement. CONFIG_PM_DEVICE_RUNTIME=y, which I used, causes that twi driver doesn't start. I try to...
In the nRF5340 Audio DK example located at C:\ncs\nrf\applications\nrf5340_audio , I want to add a third board and communicate with it from the master (gateway) to send commands...
Dear NRF Team,
I hope this message finds you well. I have been following the steps provided at the Dev Academy for the initial setup of the IDE. However, I have encountered...
Hi,
I'm trying to use the HCI UART sample to provide Bluetooth support through UART. At first I want to test it between two Nordic Boards, but later switch to another MCU...
Hi, I am facing an issue while integrating BLE with the rest of my code. The code crashes when I try to start BLE outside of main() .
Currently, I have placed the BLE initialization...
Hello,
our project which started 7 years ago with SDK13.0 has been migrated some time ago to SDK 15.3 and now to SDK17.1. At the beginning we were quite happy with the RTT...
You are trying to perform RSA encryption using CC312 on the nRF5340, but the function:
returns -147 (PSA_ERROR_NOT_SUPPORTED) when CONFIG_PSA_CRYPTO_DRIVER_CC3XX=y and...
i am unable to build the unit test code with kernel file
FAILED: CMakeFiles/testbinary.dir/home/avinash/zephyrproject/unittesting/gce-source_code_latest/app/vipr/model/gas...
I'm trying to program an nRF54L15 on the nRF54L15PDK evaluation board with the DEBUG IN SWD pins (P15). On my setup I have a J-Link PLUS connected to P15 and a USB-C connected...
I have the following settings in my prj.conf:
and getting the error
CONFIG_FLASH_MAP was assigned the value y, but got the value n. Missing dependencies: FLASH_HAS_DRIVER_ENABLED...
Dear Nordic team,
we are facing a strange phenomenon - in idle mode (k_sleep(K_FOREVER)) we notice, that the current consumption drastically increases if a magnet is placed...
I have a production system running a modified asset_tracker_v2 sending temperature data to AWS. All is working fine with V2.5.0 on several hundred sensors. I am trying to...
Hi,
I am looking for procedure to make it work nRF240L01? I am getting documents for Arduino but as you know that is not understandable, with Arduino it worked but i don...
Using the Online Power Profiler for LTE we saw that nRF9160 would require 0.115 s to upload 4-kbit of data into the mobile network.
This is an U throughput of ~34-kbit/s...
Hi,
I want to make an I2C communication with an NRF5340 DK as Master and an NRF52840 as Slave, but all the example i found in I2C communication it use the slave adress...