I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
Hello,
I am using SES V4.5, SDK 15.2 and the "ble_app_blinky_c" and I was not able to see the programme log.
I tried setting up the file "sdk_config.h" to use the RTT...
Hello,
I'm starting to develop an application using the DK pca10040 and SDK 15.3. At first I have just adapted peripheral ble_app_uart example and incorporated fds functionality...
Hi,
This may be a simple question, but I've gone through the infocenter and am still a little confused. I'm designing a PCB on which I'd like to have an nrf52840 that can...
Hi,
I recently purchased the nRF9160DK but cannot connect to o2's LTE-M network using the iBasis SIM, following the instructions given here: https://www.nordicsemi.com/Software...
When I trap an error in app_error.c in app_error_save_and_stop,
I mostly get a filename, line number, and an error code that I can understand.
However, sometimes I...
We are looking for a freelancer who can help to build a simple Proof of Concept of a load cell (strain gauges) ADC (HX711?) and the nRF52 development kit (810).
Objectives...
Central and peripheral is pairing and bonded. Central scanning with whitelist, if Slave is not online, master scan with whitelist will enter error when more than 30 seconds...
I'm using whitelist when bonded, but I want delete bonded then connect to anther device,.
But when scan again, whitelist_load is error. Try delete whitelist at the same...
Extended corruption occurs if DMA transfers for commands and data originate from the same RAM bank.
It is avoided if transfer of command bytes and transfer of data bytes...
Hello,
I ran into this list recently: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcomp_matrix_nrf52840%2FCOMP%2Fnrf52840%2FnRF52840_ic_rev_sdk_sd_comp_matrix.html...
Hi,
I'm using two nrf52840 Dev Kits and am trying to test out the ATT_MTU throughput example with SDKv16. Whenever I program one of my boards I get repeated fatal error...
I am pulling my hair, literally , I just can't get this company !
I am working with 4 IDE's in parallel and none of them has this stupidity .
I right click->add a new...
Background
I intend to use an nrf52 based board in remote inaccessible locations. It is important that I can always recover from a problem. As such, I want to use the watchdog...
Hi，
In the 07-5123-07-zigbee-cluster-library-specification specification, I see clusters that support CO2 and HCHO, but I did not see any definitions of CO2 and HCHO (cluster...
