Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hi noridc,
I am using the sdk 15.03, s140 and the nrf52840.
I used as a reference the ble_app_interactive experimental example and the ble_central/ble_app_hrs_c. My...
Dear Community, good morning
I am working in a design that do not use USB port. If VBUS pin is left floating could it cause any issues to nRF52840.
Best regards,
Hello, guys!
I have some questions concerning GPS receiver inside nRF9160. You say in your documentation that GPS receiver supports L1 C/A reception - link .
There are...
What's the easiest way to view all logs and error messages using USB serial connection app like putty, on the nRF52840 dongle?
What drivers and functions do I need to enable...
What level of risk is involved with brownouts for the modem? We have seen some modems in the past which have bricked themselves when a brownout has occurred when performing...
Hello, I want to inquire about the functionality of nRF52833-DK if I want to communicate between transmitter and receiver for locating position of receiver using BLE (Bluetooth...
Hello ,
I am interfacing the nRF52832 with winband spi flash . I can able to read the device manufacture id but i couldn't able to read the data from the device . I am getting...
Hi,
I am using the nRF52840 to sample some channel.
I am using the nRF5SDK160098a08e2 for that and based on the saadc example.
These are the results for my tests....
Hi there,
I've been unable to find a good example of what settings are required specifically to ensure that a characteristic's value can only be read and notified in an...
I have a question regarding the nRF Toolbox App v5.0.2 on iOS 14.1 and the Cycling Speed and Cadence demo app. It appears to be that the km/h calculation based on the CSCS...
Hi
I have created 4 threads in nRF9160 application, I have to go to sleep if none of the thread is running.
For this how do I check whether the created threads are running...
Hi, We are working on nrf5340 with the nrfx I2S implementation. We have configured the I2S IRQ for every 5 miliseconds. However, we have observed that successive IRQ introduce...
We are testing the combination of hrs example and the code in the butonless example. When I tried dfu after putting the code together, this error occurred. What does this...
I am trying to interface the microphone with nrf52840 and using the PDM interface. After initializing the module (nrfx_pdm_init) and then set the buffer , I do see clock and...
Dear Sir.
I have some boards that work with nRF9160 and Chipsim.
Some work fine.
Using MQTT application
With two boards I get the errors.
ERROR: getaddrinfo failed...
