Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I recently purchased the nRF5340 PDK. I am working through the getting started guide and can't seem to get the Heart Rate Monitor demo application working.
Firstly, when...
trying to get nrfutil working on ubuntu, following this guide:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nrfutil%2FUG%2Fnrfutil%2Fnrfutil_intro.html
after...
hi, I have used to segger j link basic with nrf connect programmer to program mass production.
but, It takes 30 seconds. For better efficiency, can It be improved to change...
Hi Everyone,
I need to develop a bootloader and a firmware update procedure.
My development environment is nRF52840, sdk 15.3.
Program download configuration 1) Download...
Using Mesh SDK 3.2.0.
The returned Device Composition Data is malformed when requesting it after the node has been reset. This is because the sig_model_count and vendor_model_count...
Hi to all,
i am trying to develop an app with NRF52840 soc and nordic sdk 15.03. in my app i implemented a usb hid device and also i am using flash storage at same time...
Hi
After getting SDK16 , we have tried to load a combined hex file with bootloader + S132 V7 + application with dfu + bootloader setting page to PCA10040. And It work well...
Hi,
i am working with aws-fota example, i copied my certificate to certificate.h file, once i run the program it shows like
The MQTT AWS Jobs FOTA Sample nrf_inbuilt_key_delete...
Hello, I started to delvelop an program from mqtt simple, now that I almost finished I saw that mqtt is refusing to connect to my broker, I deleted all my code I wrote and...
hi ,,, nrf52832 , at first for bonding i will connect my device manually by scanning and after passing the data to flash , i will disconnect . in program i have set the timer...
I'm writing test code to verify the softdevice operation according to the spec.
The goes like this:
The central sends the feature exchange command, when the feature exchange...
Hello,
I have been experiencing corruption using a similar implementation to the USBD_MSC example. Even after the various SDK fixes suggested to the same problem outlined...
Hi Øyvind
I can't programing the target board.can you tell me On the "debugger" nrf9160DK ,What do I need to set?
I followed the Settings below:
On the "debugger" nrf9160DK...
Hi,
I am trying to setup a ble sniffer to make sure another one of my devices is sending the correct data to the central. But the nRF sniffer does not seem to be picking...
