I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
I used SDK v2.6.2 with the nRF7002 DK kit.i used mcu boot secondary with external flash.
I was able to perform OTA using the nRF Connect app, but after resetting the DK...
Hi,nordic team
I am programming with ncs v2.9.0,nrf52833
And i am doing central multilink whick should support max 6 peripheral devices connected.Now it can connect to...
Hi:
I purchased the nRF5340 Audio DK and used NCS 2.5.0. After flashing the unicast_audio_client example (zephyr/samples/bluetooth/unicast_audio_client), it failed to run...
Our project is built wit NRF Connect SDK 2.9.0. For the UART we use nrfx_uarte library directly.
RX works perfectly, but TX is working only in blocking mode. If I call ...
Hi,
I designed a custom NRF52832 board and need to connect it to an ESP32 board. I soldered five boards for testing and also have an NRF devkit.
However, the ESP32 only...
My platform is the NRF5340 , coupled with 32MB of external flash , so I have plenty of external storage available. However, there's a risk that my project may eventually outgrow...
Hi there,
we're currently in the process of changing our hardware to use the nRF54L15. Since all the security regulations are getting stricter and stricter and the support...
Dear Nordic Support Team,
In the datasheet of the nrf9160 (nRF9160_PS_v2.2.pdf) the VSS pin appears in the section 6.4.5.1 GPIO Electrical Specification, but I cannot find...
I'm looking at Product Specification v1.2 - Reference Circuitry Configuration 2 where BUCK2 is not used. The schematic shows the output VOUT2 is tied to VSYS in this case...
Hi Nordic Team,
I am planning to develop a Matter-over-Thread end device (sensor) using the nRF54L15 , which will be battery-operated . To maximize battery life (minimum...
Does anything exist yet? The datasheet only contains a preliminary matching network and says will be available when the chip enters mass production, but nothing is available...
Hi,
I'm trying to use the HCI UART sample to provide Bluetooth support through UART. At first I want to test it between two Nordic Boards, but later switch to another MCU...
I tried used Nordic's UART service implementation as a starting point and everything works but I can't figure out where the string "Nordic UART Service" from "nrf connect...
I have loaded the Quick Start Application using nrf connect for Desktop after following the instructions. I get the error as per the attached file on the Serial Terminal....
Hello,
We are trying to test our custom board with nRF9161 in a new location, so we bought local SIM cards (Yettel, Serbia) here. These are not special nb-iot SIMs, just...
