Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
To preface:
nRF Connect SDK 2.9.0
nRF9151 DK
Windows 11 PC
Hello,
I just stumbled upon a potential issue after trying to figure out why I couldn't use 'softreset...
Hello, I'm having problems trying to make the MODBUS RTU Client code work on my board.
I'm devoloping with nrf Connect SDK v2.1.0, using Visual Studio Code.
The board...
I build the NCS 2.9.1 connectivity bridge with
west build -b thingy91x/nrf5340/cpuapp
when I try to flash that with jlink, I get
west flash -- west flash: rebuilding...
Hi I'm trying to get more insight about nRF7002 power supply requirements. My last question didn't get a follow up so I guess a block diagram of the internal power arch was...
What would happen if a battery were connected in reverse to the nPM1100? Would it cause damage to the IC, trigger any protection mechanisms, or result in abnormal behavior...
When Developing with nRF5 SDK, follow the Developing for the nRF52805 with nRF5 SDK - Getting Started - nRF5 SDK guides - Nordic DevZone 。
The Peripheral UART Example runs...
I am having issues using a keypad to wakeup an nrf52840 and am unclear on if the GPIO sample is relevant if using a kbd_matrix device definition. I would like to use "sys_poweroff...
Hi Nordic,
I have a general question about kernel threads in the mesh stack. From memory, Bluetooth has its own thread in the stack I think. At some point in the stack the...
Hi,
As title, please help to share the required information for nRF52085 pre-design evaluation, thank you.
1. Reference schematic & layout file & guidance.
2. Design...
I've installed Visual Studio Code and nrfutil and nRF Connect and J-Link and managed to compile Blinky and flash the Thingy:91 X using the terminal:
./nrfutil device program...
Dear all,
I’m working on a project using the nRF9151-DK and need to implement frequent data transmission via LTE. My setup includes multiple I2C sensors, and I want to send...
Hi everyone,
I am getting this build error while I am trying to call a function from gpio.h in my custom code
Looking at my includes I see this
This is a really...
Hello,
I'm just starting with the Power Profile Kit 2. I've read all available documentation but I didn't find any information about the switch SW1 called 'POWER'. There...
Hi,
I'm using an nRF52810 on a custom board and I'm using softdevice s112_nrf52_7.2.0_softdevice.hex.
I want to write some information (just 4 bytes) to flash memory,...
