Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’. Currently it is SystemON mode. But I need to change...
Hi,
I am having trouble running the ANT+ examples on the 15.3 SDK. I'm testing on a NRF52832 DK (PCA10040) and I'm trying to get the ANT+ examples working on SDK 15.3, in...
Hi everyone
I was testing the bonding with MITM settings. I used the code from the following link: github.com/.../nRF51-ble-peripheral-bond-handling . I tested the bonding...
Is it possible to generate a pre compiled library that configure at run-time new BLE services and characteristics on the nRF52840? If the answer is yes, is it possible to...
Excuse me, I have a question on calling external function.
board using: nrf52832
softdevice using : s132(6.1.1)
The situation: There are two applications which is...
Hi
I am using PCA10040 in order to develop nrf52 firmware. For now I would like to try to measure current consumption.
Is there any couple of pins on the board I can use...
I've been doing some testing with the nRF52840 (I purchased the Raytac MDBT50Q-1M), and I'm seeing a pretty hard startup surge. I've attached the results from my scope. The...
Hello,
I have some problems when running the development kit. It seems the problem might be somewhere on the PCB, something related to power sources and power distribution...
Hello,
I try to make my NRF52832 communicates with a memory (MX25R1635FZUIL0) in SPI.
When I try to read the memory ID, the RX buffer is fill with 0x00. But when I observe...
Am facing issue when am reading data from controller(UART) and using ble_app_uart example code to send data to BLE.
Not able to use two uart's at a time.
My setup: nRF52832 with nRF6707 on top. My embedded application synchronously exchanges UART messages with a desktop application that feeds it data (on demand from embedded...
I use nRF52DK as a central using ble_evt event BLE_GAP_EVT_ADV_REPORT to get RSSI from the peripherals when they are advertising. But once the connection is established, how...
Dear community,
I'm having some trouble configuring and adding subscription addresses to one of my node's Generic On Off Server model. This devices is composed of the usual...
I am new to GATT services and characteristics. I have written one custom service with two characteristics for my custom board. I have used nrf 52832 with sdk 15.2.0 and referred...
Hello,
I am trying to connect to my nRF52832 through J-Link v6.22g. This version doesn't contain the RTT Viewer GUI, but instead I am trying to connect through the RTTLogger...
