At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hi team,
I downloaded nRfgo studio , keil compiler,and sdk 12.1 version and i able flash ble_beacon example on nrf51 dongle.I have www.nordicsemi.com/.../nRF51822-Development...
The work I finally have to complete is,
It is to port nRF 51822 project to nRF 52832.
There are two kinds of projects, KEIL and mBed.
Could you tell me the best way to...
I would like to know the files contained in nRF5x_MDK_8_9_0_IAR.msi
as well as other files needed for a minimal application.
I would like to know exactly which are those...
Hello iam using softdevice 110 and SDK 10.0.0, i want to know the way to avoid bonding of device more then once, or deleting the bonding information from persistent memory...
I need to change the flag of the scanrsp. I use the advertising_init() and i try to do like this:
scanrsp.flags = FLAG;
but the function ble_advdata_set(&advdata,&scanrsp...
Hi,
I'm tring to generate private key of dfu, but it didn't work fine.The following is my steps.Did I miss something?
C:\Users\Administrator>cd C:\Program Files\Nordic...
I'm trying to tune a chip antenna for nrf52832. I am not an RF engineer but have figured out how to get the basic VNA measurements done.
I've been fighting with finding caps...
Are there any dirty hacks to pass a little data, like 1 bit even, during pairing?
I need my central to tell the peripheral orientation, left/right, as early as possible....
I am using an nRF52832 PCA10040 board, using s132_nrf52_2.0.0_softdevice.hex, and have AIN0 connected to a potentiometer similar to this . The power input pin is connected...
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Hello,
So — in just trying to get the blink example working, I've come across all kinds of toolchain weirdness. I'm using CrossWorks, because it's on OSX and it's way cheaper...
Hi all
Is possible from softdevice or from program application edit the GAP service? I know this service is mandatory but what about edit the structure which is shown on...
Please give me a professor.
In the nRF 52832 sample project, there is an NRF_LOG_INFO function, is this the ability to output a debug string to the UART?
If so, how can...
I have custom service, where I have declared 2 handles inside BLE Service structure, one for button action and the other for custom battery ADC measurement, each identified...
