Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hello,
I use SDK 11 with nRF52, softdevice s132.
I am able to successfully use the bootloader in serial mode (with UART) to upgrade the application, but an error occurred...
hi nordic,
After i received this kit from Mouser Electronic, when i got it check the board which some question,
we examined its outward appearance and found that this...
Hi,
I have my nrf52 DK. I would like to advertise as Beacon and be BLE (which I can connect to via iOS app) device at the same time. Do you know any examples of this kind...
Why does the macro CHECK_RAM_START_ADDR only check for C_LINK_CNT and P_LINK_CNT and not the SEC_COUNT? It is always set to 0 in the macro.
I have increased the central_sec_count...
Hi ，
I use timer to handle pwm signal,
1.when calling button by phone is pressed,
Timer starts,(function:on_key_trig_speaker_event())
2.pwm signal run (speaker_meas_timeout_handler...
Hello,
My name is krishna,
I have couple of NRF24L01+ modules,
I am trying to implement MultiCeiver in the NRF module.
The problem is i am able to receive or transmit...
Hi,
I am trying to compile the ANT Broadcast Tx Example from the latest nRF5 SDK v12.1.0 (../examples/ant/ant_broadcast/tx), but I get the following 3 error messages with...
Hi,all
I use nrf51822 connect with ios device,it will automatically disconnect when links more than 90 seconds.
device connection parameter as follow:
#define MIN_CONN_INTERVAL...
Hi I'm using the Jlink to program nRF52832_XXAA, by using nRF command V9.0.0 nrfjprog
I success in erase , but I can't program correctly,I tried Jlink version 5.12g and 6...
initially we developed code for arduino mega board but now we want to use the nRF51822 soc,so how i can utilize my arduino code for nRF51822 ....i have gone through the some...
Hi,
I'm trying to load the secure_debug bootloader for the nrf52 with the SD 132 3.0 and an aplication.
But when I load the aplication the bootloader gets erased or overwritten...
I've got a problem to change polling method to interrupt notification on open-mesh with freertos project.
The example "BLE_Gateway" of open-mesh as flow:
if (rbc_mesh_event_get...
Hi i have to use this accelerometer and connect it through i2c
www.analog.com/.../EVAL-ADXL345Z.pdf
This is my connection:
VIO --> 3.3V
GND --> GND
CS --> 3.3V...
